Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

07/10/2021

 Audi Charles Boroughs (130Pts.)

0

2018 Audi A4 Manual transmission wire

Need guide for manual transmission on 2018 Audi A4. Can't find any info
Login to reply View 1 answer(s)

14/03/2021

 Audi michael leung (150Pts.)

0

(+) clutch bypass wire manual for audi b8

Hi there I am trying to install a evo one in a 2009 manual audi s5 but i am having a problem the yellow line which connect to (+) clutch bypass are too short to connect under the hood. i know i can cut the orange and white line and to extend to connect to the hood but i want to know is there another way to connect to the clutch bypass instead under the hood is there like another wire near the the clutch pedel? thank you mike
Login to reply View 1 answer(s)

05/03/2020

 Audi Daryl Keyser (130Pts.)

0

2011 S4 (manual trans) doesn’t sense key while still in key port after a normal start.

Hey, Installed EVO-ALL with separate remote starter using t harness. All commands/triggers work as expected from the remotes, including remote start (and key takeover when remote started). If started normally using the key port, the car starts, but key is not sensed in the port so once a door is opened/closed, reservation mode will set with the key still in the port, then shutdown the engine. I'm using the CM7000 - should I splice the Key Sense INPUT (of the CM7000) to the "Key In" (EVO-pin A20)? I thought this would have been communicated over data, but maybe not. Any other ideas, or suggestions? Car: 2011 S4 Manual Trans. Keyport Service #: 001A06901001 Thanks.
Login to reply View 3 answer(s)

05/03/2020

 Audi Stuart Pullen (190Pts.)

0

2009 S4 MANUAL TRANS, NO START AFTER 3X LOCK

Hello, I have a manual trans Audi s4 2009 keyport Evo One , i have installed the T-harness - yellow line from 6 pin to the clutch bypass (red/blk) in engine bay as per pics, Canbus High and Low installed correctly and the Pink from the 6 pin to the purple/ yellow to convenient ignition out. I have the module programmed as per intructions and no error. when connect all the plugs and lock the car then try 3x lock to RS nothing happens. I see the module flash with a blue led at every lock and unlock but no ignition. Evo One S/N 002B04 013291 Thank you in advance! Stu.
Login to reply View 1 answer(s)

17/02/2020

 Audi Ken Stevens (150Pts.)

0

What components do I need for a 2011 Audi A5 with a manual trans?

Hey Guys.... Been trying to figure out what exactly I need for my car and it's a little confusing. I think I have it figured out and just need a confirmation before I buy!

I have a 2011 Audi A5 with a manual. If I understand the terminology correct, I believe it is a key port version (FOB into dash and push that to start). I DO NOT have a key to sacrifice.

I think I need:

    EVO-ALL (key port version) T-Harness (to avoid hacking wiring, correct?) FlashLink Updater (to program keyless?) Evo 9 Series Remote (to start far away)

Is there anything else I would need?

Thanks... looking forward to a nice install and a great system by all reviews!!!

 

Login to reply View 1 answer(s)

03/06/2019

 Audi Nathan Crim (180Pts.)

0

2009 Audi s5 manual evo-one with thar-audi blue led stays solid will not program

2009 Audi s5 manual transmission, keyport and start/stop button with evo-one with thar-audi t harness. The blue led stays solid when the ignition is turned on with the keyport and I am unable to program. I have checked the yellow starter wire connection to the clutch bybass and the connection seems solid. The 12v to the juction box is getting a reading and good. The can high and low are also connected good. The connection for the vehicle is clipped together and the plug for the evo-one is connected as well. The 16pin is also plugged into the keyport. When I plug the data cable in while holding the program button the led turns blue. I plug in all the other cables, insert the key, and press once WITHOUT pressing the brake. When I press and release the the program button the blue led remains on as if nothing has happened. Any help please?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue