Questions & Answers

I installed the EVO ONE without T-Harness and RFK411 on a 2014 Scion XD (with standard key). Sometimes after remore start, when the door is opened the alarm is set off and the remote start is halted. Option D2 was inititially turned off.  I turned it on and though it improved quite a bit, it still happens every now and then.  The system is wired and configured per Guide # 102241.  Any help would be greatly appreciated.

No immobilizer, did not connect light blue/ black wire, module programs ok by letting go of button on blue, and the flashes blue rapidly after turning key to on. 
 

​I already tried connecting the immobilizer wire & programming again. I already tried programming using red & blue light but that won't program. Using Fortin guide #23001. Not "G" key. Verified no immobilizer/chip on key. Won't remote start with lock 3 times on key. Won't remote start with the MyCar app module.

I received the EVO-All KIT and already flashed the newest firmware. I just want it to be a standlone with 3 locks remote start function to work. I bought the THAR-MAZ1 to my life easier. I've read the diagram and my understanding is we have to do some wire tapping in order to make everything work. Is there a way for me to make it a standlone with 3 locks remote start to work without doing any wire tapping ?

hi,i have few questions that im having issues with my 2008 scion Tc A/T 
EVO-ONE SERICE# 002B07 164975
T-HARNESS
fortin ftx64-1W remote
ive already connected pretty much all wires needed i believe, i can remote start the car,antenna led is blinking,horn responds when unlock/lock button is press,but doors does NOT lock or unlock, i do have the purple & purple/white connected to the proper wires on the vehicle. Also i did turned on unlock/lock before and after remote start and driver side will unlock before remote start but will NOT lock after, also have the lock after foot brake and unlock when ignition is shut off programmed but door locks also doesnt respond to it.
and lastly alarm does NOT trigger,im inside vehicle arms vehicle wait a few sec then i manually unlock door and open but the alarm does NOT trigger,the only time it works is when i press the panic button.
when unlocking the doors with the factory keys i have to hit unlock button twice for all doors to unlock.not sure how that will work with rf kit remote.
also on wirecolor.com i notice theres wires for door pin FL(orange) and door pin FR(blue) on the vehicle, but i don't know which wires will i connect from the evo module to those wires if is needed.

please get back to me asap
thank you very much 

The trunk release button on the Revo4.1 remote does not work at all with the car running or not.

The doors lock and unlock  and remote starting is working  using the revo remote.

I recently got my evo one today, and installed it after some back and forth with the firmware and the updates. It starts using the lock-unlock-lock feature (did this so that the alarm is in a disarmed state when the engine starts, so no need to splice into key sense)  However, when I start the car using the remote, nothing happens when i go to try and unlock the doors using the remote. I know that the car ignores the remote with the engine started, and I can see that the evo one is recieving the lock and unlock commands from the vehicle(can see blue light blinking with each key press ) but I'm unsure if the doors are supposed to unlock with from the can hi and can lo connections, or do i have to splice into the door lock and unlock wires in order for the  door to unlock? 

I bought the Evo One and i'm having a problem to get it working. I followed guide# 23001, REV:20160601, wiring done and at programing step 5, when I turn the key towards the "on" position the red LED begins to blink and it does not stop. For I have purchased a used car, and it had come with two keys, with one having a Scion logo on the back and a Toyota logo on the other key. The Scion key does not have any stamp marks, and the Toyota key has a H stamp on it. The vehicle I bought was certified by Toyota. To test if my car has a immobilizer I had cut a new key (no chip) in the local hardware store. The new key started the car, while the original keys were in the house twenty feet away. And I googled that only the Canadian xB needed the bypass module. So the question is whether or not the unit will work for the car and how to wire and program it in said vehicle. The firm-ware was installed at the place that I have purchased the Evo One.

EVO ONE WITH THAR-TOY1 THARNESS

In my 2014 scion xb, plug to light switch at pin 12 do not have wire can I just ignore this connection?

I go through all the steps and but but when I connect the EVO ONE the second time to read the sample of the immobilizer I get:

The module was not able to sample the vehicles immobilizer data.

I have tried multiple times and sometimes after I start the car the red light doesn't blink and sometimes the red light blinks while the blue led is steady on then the blue led flashes then the red and yellow alternate. This makes it take longer but I have had it go through the regular steps and still the Dcryptor part is not getting my car's data.