Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

User

Charles Cho

Joined on the:

Nov. 30, 2014

Score

380

Comment(s)

12

Voted question(s)

0

Voted answer(s)

2

Votes up

0

Votes down

2

Votes up received

0

Votes down received

0

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

0

EVO-ONE Pit Stop Option? (2017 Tundra)

While the vehicle is running, if I put it in Drive, press the keyfob's lock button 3 times, and remove the key, the vehicle remains running. If I exit the vehicle and attempt to lock it by pressing the lock button on the fob, the vehicle does not lock. Is this "pit-stop" mode even supported on EVO-ONE? And if so, how can I lock the vehicle whlie it's running without a key in the ignition? bypass: 002b02125187

0

Explain these options please (bypass side)

I finished installing EVO-ONE on my '17 Tundra.  What do the following settings/options do?

  Options A1 - A10 Am I to blindly enable all of these options?  Currently I have the default A1 - A9 enabled, but A10 is disabled.  What are my ideal settings, or do these settings not matter for my install?   Option B1 - Unlock Driver Door Only This option is disabled, but vehicle acts as if it's enabled. (FYI, vehicle's stock head-unit has a setting for this enabled.)  Does the vehicle's setting override the EVO-ONE's setting?  Or does this option not even apply for my install?   Thank you in advance.   Remote Starter - 002B05017153 Bypass - 002B02125187

0

Explain these options please (remote starter side)

I finished installing EVO-ONE on my '17 Tundra.  What do the following settings/options do?

  Option 9 - Active or Passive Starter Kill What does this do?  I am using the EVO-ONE as the bypass and remote starter.  I do not have a separate alarm or remote starter installed.  Does it even apply to me?   Option 11 - Confirmation I currently have 11.1 enabled (I think by default) but my vehicle chirps on every key fob press. (Option 11.2 is for "Lock/unlock sound always," but, like I said, option 11.1 is enabled.  It's as if option 11 is ignored or vehicle's settings override this option.)   Also, what is an "Antenna LED?"   Option 15 - Smart Door Lock It is currently set at "15.1 Disable," but my vehicle automatically locks the doors if it doesn't open after a certain amount.  (And I can set that time value through my vehicle's stock headunit.)   Option 20 - Engine Supervision What is this?  I have no idea.   Thank you in advance.   Remote Starter - 002B05017153 Bypass - 002B02125187

0

No Fuse When Using T-Harness?

I am preparing my wires for EVO-ONE install on '17 Tundra. I'm going to be using the T-harness to do the install. I noticed there is no fuse on it. The non-T-harness install specifies a 30 amp fuse on red ignition harness. Do I need to add a fuse to the T-harness?

0

Trim Lengthy Wires?

What do you with lengthy wires? Do installers trim them or loop them and then zip-tie them? (I know about de-pinning unused wires and that is not what I'm asking about.) Thanks in advance!

0

Car Won't Stay On after Uninstalling EVO-ONE

I uninstalled my EVO-ONE on Subaru 2015 (standard key). Car starts, but shuts off after a few seconds. What's going on?

0

Dashboard Immobilizer light constantly dim/pink

Ever since the EVO-ONE was installed on 2015 Subaru Outback 2.5i (Standard Key), the dashboard immobilizer light has been dim.  It is dim/pink when the car is in off state or running state.  Everything seems to be functioning correctly.

Do I have a defective EVO-ONE?  Or is it a wiring problem?

 

 

0

What are the proper functions, modes, and wiring for anti-grind and starter kill

I am looking to add anti-grind/starter kill on my 2014 Toyota Tundra. Here is the setup I am planning on using. - Function 32, Mode 4. (dark blue wire A8 set to "starter-kill") - Function 10, Mode 1. ("starter-kill and anti-grind") - Wire in a spdt relay using the normally closed circuit. With Ignition 2 and the dark blue (A8) wires hooked up to the positive and negative side of the coil respectively (posts 86 and 85) Is this correct?

0

OEM FOB 3X lock, car starts, alarm goes on and can't turn off with FOB

2014 Tundra. EVO ONE with T Harness. Picked up truck at the dealear and worked perfect. Press lock 3 times and engine starts. Press unlock and enter truck. Put key in and turn to drive away. Perfect. I get home and show wife and imediatly the alarm goes off. FOB won't work. Put key in door and alarm stops. 2 seconds later the truck starts on its own and starter stays engaged for several seconds after the start. Put foot on brake and truck stays running. Try putting in gear and engine turns off. Anyone know what could have happened?

0

Doors do not lock after EVO-ONE 3XL remote start

I have a 2015 Subaru Outback (Std Key, Automatic) with EVO-ONE only install. All keyfob button functions work but after 3XL remote start, the doors do not auto-lock. Function is enabled in settings, but I do not get a door lock after remote start. I've also tried wit 6.2 enabled. side note: I actually have lock-unlock-lock enabled for remote start because 3xl makes my car horn honk on the 2nd and 3rd press. Anyway, I noticed that the Evo-one is inconsistent and unreliable when detecting the fob button presses. What I mean is that the doors will un/lock everytime I press the fob buttons. However, the evo-one blue LED does not light up everytime the fob buttons are pressed. This leads into the Evo-one not recognizing the command to remote start the vehicle. Any thoughts on this issue?

1

Wire missing / inconsistency with manual instructions. No IMO wiring

Trying to install an EVO-ONE but car does not have IMO wire.

 

Consider the following photo from the installation manual:

 

 

And take a look at my car's wiring:

 

 

The IMO wire is missing.  What to do in situations like this?

 

Vehicle is a 2015 Subaru Outback.

1

2014 Tundra wont crank EVO-ONE with harness 3X lock

Purchased pre-flashed and tested. The EVO-ONE programs correctly and blue LED flashes when key lock pressed. On third press a click from the EVO and red LED comes on. Second click from the EVO after about one second of the red LED illuminating and then nothing. No further LED's no crank attempt. I have verified continuity on all connected wires from origination to EVO connection harness. I have also verified correct outputs from EVO t-harness to correct ignition wire per the 2.4 programmable output options the EVO is programmed to and at this point completely out of ideas. I appreciate any insight.


Thanks

0

Ax-One / EVO One Lights issue on 2015 tundra

hi there, i just had my evo one system installed today on my 2015 Tundra, the installer mentioned he had a hard time finding the parking lights or something along those lines, he said the guide was wrong ( i gave him both guide #18211 as well as the wiring diagram from wirecolor) i didnt really think anything of it because the remote start works but on my way home I realized something strange was occurring. Sometimes the lights on my dash / guages goes out which made it impossible to see my speed at night, also once i enter the car and the lights turn on then go out but as soon as I shift from park to drive the interior lights come back on for about 10 seconds (really annoying). As far as my dash lights I can get it to come back on if I put the truck back in park then drive again, it resets it. Lastly, whenever my guages are out, Im also unable to activate my fog lights ? but again when I move the shifter to park and back to drive it resets everything and im able to get my fog lights back on. any ideas of what might cause this ?

0

Evo-One for 2014 Toyota Tundra 79.20 Hood sensor was diabled to remote start.

Hello, I installed Evo-One on my vehicle yesterday. 2014 Toyota Tundra. I called support this morning because the remote start was not working. After the calling the support, he had me disabled the hood detect because was constantly flashing five times when I try to start the vehicle. I just tried again and set to detect hood and it would not start and flashs five times. I disabled it again and it works fine. Is this a bug with the firmware? I am running 79.20 and 1.15 on my Evo-One. Support checked that there is nothing connected to one of the wire for hood switch. I did not install the hood switch. Wondering...

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue