Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

User

Michael C

Joined on the:

Apr. 2, 2017

Score

160

Comment(s)

2

Voted question(s)

0

Voted answer(s)

0

Votes up

0

Votes down

0

Votes up received

0

Votes down received

0

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

0

evo-one, 6 pin harness, rs programming, Wrangler

Hello, I require some assitance from you with an installation. I have been reviewing the diagrams shown in the install manual # 16561 and the quick install guide for the installation of an EVO-ONE with the CHR5 t-harness onto a 2016 Jeep Wrangler with manual transmission. I have also reviewed mutliple other EVO-ONE install guides as further information sources as well as searched the forum prior to asking this. So that you know where I am, here is what has been done so far: I have installed the valet switch. Connected the 3 pin to a dual stage shock sensor. On the 20 pin connector I have added a siren to pin A7, connected the hood pin to A15, and connected the A1 yellow to the t-harness yellow. On the 6 pin white connector, I have connected the white E1 wire to the white and purple parking light wire at the kick panel on the passenger side of the vehicle, connected the E3 power to an unswitched 12v power source, and connected the E4 ground to a suitable body ground location. Where I am lost is that on the white 6 pin connector, there are also the E2 orange, E5 pink, and E6 yellow wires that are currently unused. Addtionally, there is no reference to the use of any wires other that E1 and E3 on the instructional schematic. I assumed E4 ground due to E3 12v power is used. The EVO-ONE quick install guide states that E2 is (+) ACC/IGN2, E5 is (+) ignition, and E6 is (+) Starter. Additionally, while programming the unit with the flash link, function 2 and function 31 make reference to using the white, orange, pink, and yellow. I know that function 31 should be set to mode 4 since I am using the white wire for the parking lights. What I do not know is: A) In addtion to the wires I already have connected (E1, E3, E4) on the white 6 pin connector, what else needs to be connected and where? B) What mode should function 2 be set to in order to be consistent with the function 31 mode 4 setting? I am asking prior to final testing so at this time, I do not know if this will work as is set up currently. Just trying to get final confirmation of correct wiring for your product instead of frying either the unit or some wires in the vehicle. Thanks in advance for your help edited final line from firing to frying.

0

Hoodpin configurations

I have read a number of posts regarding the hood pin but it seems that they discuss which wire to connect to in order to be a kill switch for the Evo One remote start function. As I understand it, the Evo One A8 pin (dk blue wire) is the trigger for the kill function. I would also like this hood pin to trigger the alarm feature within the unit in case someone opens the hood while the system is armed. What would be the correct wire to connect the hood pin to in this case and can I use one wire from the hood pin and connect it to both the A8 wire and the alarm trigger wire within the chasis of the vehicle in order to have both the remote start kill and the opened hood while armed alarm.

1

3 pin shock sensor connector

What is the name of the type of connector used for the shock sensor port and where can I purchase a connector with a wiring harness? If I wanted to add a tilt sensor and wired the trigger into the pink/black wire (A15) would it give me a proper tilt alarm response if triggered on a two way remote or parking light flash upon disarm? I know I need to tie the trigger for the tilt alarm into zone 8 for that I just dont know where to do that. Are the ground and 12v leads coming from the shock sensor port only active when the alarm is armed or are the always active?

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue