Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

User

Nicholas Meyer

Joined on the:

Nov. 6, 2018

Score

160

Comment(s)

4

Voted question(s)

0

Voted answer(s)

0

Votes up

0

Votes down

0

Votes up received

0

Votes down received

0

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

0

2006 Dodge Ram 3500 with 5.9L Diesel

What module would I need for a 2006 Dodge Ram 3500 with the 5.9L Cummins Turbo Diesel? Also, does the module have the start delay AND turbo timer?

0

EVO ONE Installation/Programming 2004 Ford Expedition

I have installed the Evo-One module and the wiring as follows: (Guide #22301) A1 of 20 pin harness (yellow) to E5 of 6 pin harness (pink) A10 of 20 pin harness (ight blue/black stripe) to RX (Pin 4) of igntion barrel connector C (gray/orange stripe) A11 of 20 pin harness (black) to Green wire for foot brake connector (above foot brake) A20 of 20 pin harness (light blue) to TX (Pin 3) of ignition barrel connector C (white/green stripe) E1 of 6 pin harness (white) to Brown wire of light selector switch E2 of 6 pin harness (orange) to accesory wire of ignition switch (black/light green stripe) E3 of 6 pin harness (red) to constant battery power of igntion switch (light green/violet stripe) E4 of 6 pin harness (black) to ground E5 of 6 pin harness (pink) to A1 of 20 pin harness and ignition wire of the ignition switch (dark blue/light green stripe) E6 of 6 pin harness (yellow) to starter wire of ignition switch (red/light blue stripe) When I go to program it, I get to the final step and the red doesnt flash ten times like its supposed to. I get to the red light, turn the ignition to RUN, then the lights show red and yellow. I wait three seconds then turn it to off, which goes back to a solid red. I pull the key out of the ignition, then reinsert and turn it back to RUN and the red light flashes once then stays solid red. I turn the key to off and pull it out of the ignition and the light stays a solid red. The firmware for the bypass is 4.18 which is recommended by the Flashlink Manager, but the install guide #22301 recommends 71.35. Could that be the problem? The remote start recommended firmware is 1.24. Could I have gotten the RX and TX wires not hooked up correctly? Do I need to run the Dcryptor? I ran the dcryptor as the intstructions said and it seemed to have worked. I'm not sure what I would need it for. Do I need to use the valet switch? If I want to install a hood pin, which wire do I connect it to of the 20 pin harness? If you could help me out I'd greatly appreciate it. Thanks.

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue