Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

User

paolo fast

Joined on the:

Mar. 13, 2014

Score

820

Comment(s)

26

Voted question(s)

0

Voted answer(s)

0

Votes up

0

Votes down

0

Votes up received

1

Votes down received

0

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

0

evoall with cm7000

Hi, is there a way by turning on off some options to keep separate oem remote and the fristech one? If i unlock the car by the oem remote i dont want the alarm disarm itself in order to keep the firstech remote the only one able to disarm the alarm. I tried to off option c1 but the firstech remote stop working and i cannot arm disarm the alarm anymore. Thanks

16/09/2019

Toyota akm (850Pts.)

0

Evo-one programming for push to start but car does not start

I just completed the programming for my 2015 rav4 push to start (Automatic transmission) and car does not start after 3x lock.

Is there anything i am missing. I used T-harness Toy6 which looks fairly simple to install.

Wiring diagram shows optional wire from push connection to start button which was not clear to add.

https://cdn02.fortin.ca/download/70381/evo-one_ig_thr_bi_toy6-corolla-rav4_2014_pts_a_70381.pdf

0

CM7000 + evo all

Hello i m using standard installation with t harnesses, i cannot find a specific guide of evo-all + cm7000,

https://fortin.ca/download/87591/evo-all_ig_thr_bi_toy6-chr_2019_pts-hybrid_euro_a_87591.pdf

service number : 001A06753794

cm7000 has the connector nr.3 (Gray) with 6 pin, i connected the ground and the +12v in order to give power to the unit (i thought the voltage from the data port was enough, but it wasn't)

My question is on the pin nr. 5, guide says :

Pin 5 Green: Ignition 12V positive (+) output and input. This wire must be connected to the vehicles’
ignition for remote start and valet / remote programming. The proper wire will test 0V with the key in
the off position, 12 V (+) while the key is in the on position and 12V (+) during crank. Note: this is a
low current ignition output and will not support more than 1A (+)

 

Do i have to connect this wire to acc of my vehicle only for remote programming or it should be connected as permament? The evo all should give info of ACC ON to the cm7000 so this connection can be avoided right?

P.s I see the both cm 7000 and evo all are remote starter but i have to use the evo all as remote starter not the cm7000, so when i launch from the compustar remote the remote start routine how it works?

0

Evo all without ft-d100

Hello, latest compustar rf.kit listed on your website are equipped with the new antennas with built in decode, i bought a conpustar rf kit but the ft-d100 is not needed (like in the evo-one) i can connect directly the antenna to the blue plug of the t harnesses, btw i cannot select in the menu options of the evoall the firstech option in the rf kit tab (in evo one i can do it). Can u implement this function with the evo all? Thanks

0

Reset flashinh counter

Hello , due to installation issues in the last month i tried to reflash the firmware six times, i solved a lot of issues but i cannot have 2way confirmation woth the ft-d100 i would try to reflash old firmwares but i reached 6 flashes, can i ask you for a reset? Thanks

0

Evoall a16 wire starter or valet switch

Hi, i m using evoall as remote starter and alarm system, 16221 alarm guide tells me i have to connect a16 wire for the valet switch but i m already using that wire as starter for remote system. What can i do?

0

ft-d100 + RF-AR2WT10-SS + evo-all

Hello, just bought this kit. I have paired succesfully but i have not 2way trasmission, only 1way. Any ideas? Thanks!

0

Tilt, shock and proximity on Evo-All

Hello, i have to connect these sensors to my evo-all. can u tell me which wires i have to choose as inputs? I have to use diodes on the trigger wires sensors ? only one diode is enough ? or one diode for every sensor that share the same input? Thanks I have dei sensors (504d 507 508) Thanks,

0

Siren alarm ok but no chirp confirmation

Hello Evo-all with toyota c-hr 2017 hybrid. I used this guide to install it : https://fortin.ca/download/87601/evo-all_ig_tsa_bi_toy6-chr_2019_pts-hybrid_euro_a_87601.pdf Evrything works cool. Today i installed a siren too, using this guide https://cdn02.fortin.ca/en/download/16221/16221.pdf I have turn on option G and Evo alarm. Indeed siren works when i open the door from inside but i have not confirmation chirps on lock / unlock. could u help me? Thanks.

0

Remote starter turns ignition on but engine is not ready

Hello i just installed evo-all on my toyota c.hr hybrid with t-harness, i m using this guide: https://fortin.ca/download/87601/evo-all_ig_tsa_bi_toy6-chr_2019_pts-hybrid_euro_a_87601.pdf When i press three times the lock button ignition goes on but the engine stays off, a/c goes on but the air is hot, the engine should crank but nothing happens, only the dashboard instrument of the car is on. The "ready" n the dashboard symbol that means the engine is ready to go is off, seems that the immobilizer has been not bypassed. I discovered also that the a16 wire even if connected or not doesn't change the result. engine doesn t start but ignition goes on.

1

WIndows roll up arming alarm

Hi, in my old module from Dei the bypass could be programmed to roll up the windows on arming without hardwire, directly from the can bus. Is this possible with Evo-All? Do i need extra modules? Thanks. Toyota C-HR 2017

0

Arm alarm only with rf kit remote

Hello ,Evo-all acts as remote starter and alarm system with rf kit. Can i disable the arm/disarm function of the oem remote in order to arm/rearm the alarm just with the external remote of the rf kit? Thanks.

0

Can't find new Lexus Ct 200h 2018 in vehicle list

Hi guys , i write from Italy, i wanna buy the evo-all for remote start my new car and as a security alarm. In the vehicle list i can't find the Ct-200h 2018 , you have 2017 compatibilty but i cannot find the new restyling made in the end of 2017, my car is the new restiling ( january 2018). Another question : the manual of evo-all installation for the ct-200h 2017 says : *compatible remote start required, the evo-all is not enough to remote start the car? i have to buy an additonal remote starter? Thanks Thanks

0

Compustar prime 2way communication doesn’t work

Compustar prime 2way communication doesn’t working but working perfectly as one-way. I have connected ft-d100, with blue and white wire swapped as it was in guide, idk what’s the problem,

0

T9 not programming though Ft-D100 with EVO-ALL

I have a EVO-ALL installed in a 2014 ford focus hatchback with a key start, and i'm trying to add a compustar T9 rf kit to it. I have installed the FT-D100 (switching the blue and white wire before pluging into the unit) to go between the two and flashed the correct firmware for the unit. When I replug the 4 pin connector and go into the programing mode the lights do not flash. I do get all lights on when in the programing mode but it does not seem to see the remotes.

1

EVO-ALL + FT-D100 w/ 2 WAY COMPUSTAR- Lock doesn't work

I succesfully paired the Compustar G9 2-Way antenna via the FT-D100 RF decoder but locking does not function on the Compustar remote. I get a success chirp / green flash on the fob and I can see the EVO-ALL recieving the command but it never actually locks. Unlock & Remote start work perfectly. I have tried swapping the blue/white on the data link back to see if it is a communication error as well. Is there something I need to enable on the EVO-ALL aside from the FT-D100 RF option? Another weird note. I couldn't get 2 way notification to work until I unplugged the canbus and plugged it back in after programming. Prior to that the Compustar remote was only working as a 1 way.

07/02/2015

Ford luigi (240Pts.)

0

evo all & compustar 2 way g9 rf kit+ft-d100 decoder

it works but it does not communicate back to the remote after start, is there some setting that needs to be change on the evo all? I've read that two way communication works with the evo one, its the evo all not capable of using this feature because the ft-d100 adapter impedes this?

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue