Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

Evo-Start2 2020 Forte Install question

Im installing an Evo-one with KHY2 in my 2020 kia Forte with an Evo-start 2. I've got the wiring figured out for Evo_one but the install for the Evo-start2 has me a little confused. The blue 4 pin antenna connection is obvious but im using a T-Harness (KHY2) for the Evo-one. The Evo_start install says to use the Black 4 pin Data link t-harness connector. There isn't one on my tharness. Could i get a little clarification of what i need to connect on the antenna cable besides the blue 4pin and the yellow ignition wire. The Evo-start2 install instructions shows 3 different installs for the Evo-one and all show the use of a 4 pin data connector either from the tharness or a RFA2A. The antenna cable has more connectors then any of the diagrams show. The 2 blue connectors and the yellow ignition wire are shown but the diagram doesn't show the black 4 pin female or the white 4 pin female or the other 3 wires (red,black,and green) on the antenna cable.

0

Does Evo-All need programming if my 2009 Kia Sportage thats not have a key transponder?

I’ve installed Evo-All on to a 2009 Kia Sportage 4Cyl wich is not equiped with transponder. Does this mean Data wires will not be needed? Also, How do remote start work if I cant use my vehicle alarm remote? How do I program the RF Kit for me to be able to use the remote to start the vehicle? Thank you!!

0

2014 Kia Forte EX PTS VIN8 A Couple of Questions

1st I used Guide 24661 for Evo ONE and 68731 for FL4 when installing the EVO One (recommended firmware identified on program screen, its higher than 76.36, i think there are two newer firms but it wont let me click on them, one is a beta ver.) in car to include adding 2-1 amp diodes at PTS. The car is loaded with options, heated front rear, ac front driver seat, nav and tech pack and more. So I connected laptop to FL(ver 4.05 and recomended in program screen) and FL4 to bypass/ RS and logged in, I dont see the toggle in the lower right corner they speak of, instead I can just click on the tab at top of screen and it asks to confirm or cancel(if you changed anything and didnt save) to switch between bypass and RS. Right now 3x locks the car will crank over but no run, my seat moves, Headlights and dash light up, air controls work, and radio comes on then I hear a couple clicks then the car starts to crank but acks like no fuel, What are all the settings I should have on in the bypass and starter options? I think I had to choose 2.4 in order to get it to even crank, What am i missing or need to check 2nd I see the bypass/starter has a programming set of intructions and the FL4 has its own programming setup however when save and loading setup in user interface when all devices are connected together inline, I get a message stating 20.6 will be changed but it was already defaulted with a green thumbs up, also in bypass I get a message that alot will change when those are also already defaulted with a green thumbs up...smh. Question is how do the options 2.Programmable Option and 31.4,5 and 6 work in unison with each other? Side note while creating this I just realized I did nothing with the decrypt after every thing is done with bypass and RS do i need to click send on the decrypt screen, what is the complete steps in order to complete this. Connect laptop-FL4-Bypass/RS, login, choose settings and load(save), then decrypt, then just unplug, then test or...? Update: I dont think i have a decrypt option...

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer