English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

28/10/2021

 Mazda Brandon Deason (130Pts.)

0

Program FirsTech RF Kit with Evo-One

Hello, I am trying to use an Evo-One with my 2010 Mazda 6 (standard key) with a Compustar G15 (1-way) RF Kit. I flashed the Evo-One with 71.44 Bypass Firmware and 1.25 Remote Starter Firmware. I used the suggested options. Under unit options, I change the RF Kits Compatiable option to FirsTech. I've wired up the Evo-One as the Mazda 6 2010 Standard Key guide shows. I did the 2-key programming but I did not get a response at the end. The LED stayed red and no features work on the remote. I realized that I should proabably program the remote first but I don't know how. The Quick Instalation Guide has a RF-Kit Guide # of 19941 listed. When I searched for that on the fortin.ca website, I get a 404 error. What should I do? Thanks.
Connectez-vous pour répondre Voir 2 réponse(s)

27/01/2021

 Mazda ERIC DOMINGO (290Pts.)

0

2010 Mazda 6 Standard Key EVO-ONE - Dcryptor Step 5

Hello, For a 2010 Mazda 6 Standard Key (instructions https://cdn02.fortin.ca/download/80571/evo-one_ig_reg_bi_maz_6_2009-2013_key_a_80571.pdf), I can't get the Dcryptor process (specifically step 5) to work for the EVO-ONE. The unit was removed and reinstalled, and I reflashed and master reset the bypass (Flashlink recommended 7.44 and I followed the hold down prog button while connecting 6-pin, then hold down again until all LEDs cycle). When I get to step 5, both the yellow and red LEDs are on and the red LED never turns off to proceed to step 6. If I turn off the ignition, both yellow and red remain on. I have tried the 2 key method and it will not work either. I have resoldered the TX and RX lines on the transponder connector as well. The unit otherwise attempts to remote start the car, but the security light flashes quickly on the dashboard and remote start is not successful, then the parking lights flash 4x after the failed start. Any other suggestions?
Connectez-vous pour répondre Voir 1 réponse(s)

19/01/2021

 Mazda ERIC DOMINGO (290Pts.)

0

Old instructions for 2010 Mazda 6

Do you have a copy of the old installation guide for EVO-ONE in a 2010 Mazda 6 Standard Key? I purchased and installed in early 2019 and the unit was manufactured in 2018. The new instructions say the unit has to be manufactured after 2019 but the old instructions didn't have that limitation. I had an unrelated electrical issue with the vehicle and had to disconnect the EVO-ONE and its wiring, and now that I have resolved that, I want to make sure I reinstall in the correct way with the correct firmware versions.
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer