English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

27/12/2023

 Mazda Mmk005 (130Pts.)

0

Evo Start 2 not working with Evo one with T Harness Thar one Maz3

Hello,

I recently bought Evo start 2 for my Evo one which I have been using for more than 2 years on my Mazda cx 3 2019 with T harness. At that time I did not choose the app start option while programming the Evo one. Can some please help me where should i be connecting the Yellow wire. Does it goes into the A1. Also none of the other options like door unlock are not working. Do I have to reprogram the Evo one again. I know that the firmware should be atleast 1.21. When i push start from the app the green light on the evo start 2 is turning on but nothing is happening.

I have followed the following steps and it was not working.

Ignition ON - OFF - ON (While holding the brake?)

Press and release brake 4 times

Press and hold the Evo start button until green

Turn OFF Ignition

Thank you for reading any kind of help or suggestions is much appreciated 

Connectez-vous pour répondre Voir 1 réponse(s)

16/11/2023

 Mazda Luis RG (160Pts.)

0

evo start 2

I bought an EVO-START2 to add to my EVONE + THAR-ONE-MAZ3 installation. After re-flashing do I need to do the whole decrypt process again? Also do I connect the yellow wire to A1 or E5 onto the harness? Thanks.
Connectez-vous pour répondre Voir 1 réponse(s)

10/02/2022

 Mazda Dionei Miodutzki (160Pts.)

0

Force seat heater and aux input on

Hi, I have and Mazda3 2019 (with push start and presence key) and installed an Evo One + Thar-One-Maz5 + Evo Start2.

I've connected the auxiliary output on a relay to activate the windshield heater and rear window defog (in the mazda3 both are activated together with a ground signal). Its supposed to ground the yellow/black wire when the seat/driving wheel heaters are activated right?

I was not able to test it yet, my car stays in a heated garage and if i understood correctly the evo one uses the internal temperature sensed by the module to activate or not the seat and driving wheel heaters (and the auxiliary signal). So the car doesn't stay parked out for long enough to get so cold inside. 

If i use the defrost button in the app, will it bypass the temperature control and activate the headers/auxiliary signal? If not, is it possible to change config to manually control those? 

Thanks!

 

Connectez-vous pour répondre Voir 1 réponse(s)

10/02/2022

 Mazda Dionei Miodutzki (160Pts.)

0

Wrong lock status on app

Hi, I have and Mazda3 2019 (with push start and presence key) and installed an Evo One + Thar-One-Maz5 + Evo Start2. Everything works fine, except the lock status on the app is not correct - when I leave the car it auto-locks (because I'm taking the key with me), and if I check in the app it shows as unlocked. If i send a lock command, the command is sucessfull and the status changes to locked. Going back to the car, I'm able to unlock it by just touching the handle as usual. I'm not sure if this info is useful, but during the setup I first forgot to connect the yellow wire between Evo Start2 and Evo One and paired both like this. When I noticed it was not working, I've checked all again, found the error, connected the yellow wire and paired again. The remote start by the app worked then, just left with the issue in the lock status.
Connectez-vous pour répondre Voir 2 réponse(s)

06/01/2022

 Mazda Jimmy Perron (230Pts.)

0

pas de communication entre l<antenne et le EVO-one

Bonjour, j'ai installé un EVO-ONE-MAZ3 sur un Mazda3 2016 avec une antenne EVO-START-2. Lorsque j'essai de démarrer à distance, la led de l'antenne flash vert et ensuite 1 flash ambré. J'ai lu que c'est l'antenne qui n'est pas pairé avec le EVO-ONE. Sur le schéma d'installation il y a un data-link T-harness (optionel) pour l'installation. Est-ce pour cela que ca ne fontionne pas? Merci Jimmy
Connectez-vous pour répondre Voir 1 réponse(s)

02/11/2021

 Mazda Mark Permaul (130Pts.)

0

Unable to program Evo-start 2 with the Evo One

I've installed the Evo-One with T Harness and works fine with the factory fob on my 2018 Mazda CX-5 PTS. Flashed the module to include the Evo-start 2 rf kit as well but whenever I try to program the Evo Start 2 antenna i'm unable to as the vehicle doesnt display any information nor start whenever the app is used. When "Start Engine" is clicked from the app the antenna flashes green and then amber but the vehicle doesnt start. I tried reprogramming the antenna over and over as well as reflashing the module from scratch but yet nothing works.
Connectez-vous pour répondre Voir 1 réponse(s)

11/03/2021

 Mazda Matthew cioffi (160Pts.)

0

Evo-start2 smartphone use in US

I have purchased a 2018 CX-9 and I'm going to add the EVO-ONE to the vehicle. I'm looking at adding the start2 as well. How does that work in the US, do I need a sim card and cell plan for it? Are there any additional fees?
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer