English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

04/09/2021

 Mazda Dave Lundquist (130Pts.)

0

2018 Mazda CX-5 evo one Thar Maz3 windows dont automatic go up or down

I installed EVO ONE with Thar One Maz3 harness in 2018 Mazda CX-5. Before install my windows would go up and down automaticly Just hit the button and let go. Now after install I have to hold the button until they are either up or down. How do i fix this?
Connectez-vous pour répondre Voir 1 réponse(s)

12/12/2020

 Mazda Ryan Smith3 (130Pts.)

0

Blinking amber light on start button 2016 CX-5

The module seems to work fine, I have completed every step in the installation guide. However, the start button does continuously blink amber/orange while the vehicle is running and does not stop until the engine is shut down. This only happens when started normally, not remotely. If I disconnect power to the EVO ONE, the car can be started just fine and there is no blinking light. I used the THAR MAZ 3 t-harness to install. I have been scouring the Mazda forums and have found no answer. Everyone says either replace the fob batteries (I replaced them) or visit the dealer. The mazda dealer wanted $150 to diagnose the problem, and then doesn't want to even look at it after learning the Fortin system was installed. 

Connectez-vous pour répondre Voir 1 réponse(s)

01/01/2020

 Mazda Ken Toizumi (210Pts.)

0

2019 Mazda CX-9, Evo-one, thar-maz3 T-harness

Couple questions.

For the vehicle and hardware above should I be using Guide 68271?  When I search for a guide it comes up with a few different ones that don't quite match but If I search under the Thar- maz3 it brings up this one which looks right.

If this is the right one, it says I need the Evo-one to be hardware 7 minimum.  When I connect to the flash link it says I have a hardware version 4.  Which seems odd as the sticker on the back has a date of 11/2019 (SN 002B04-060015) which I would think would be the latest hardware version .

In the guide it says I need 2 diodes.  It does not say where to hook them up or of what value they should be.

Connectez-vous pour répondre Voir 1 réponse(s)

30/12/2019

 Mazda Jonathan (200Pts.)

0

2014 CX-5 EVO one THAR MAZ3 used to work ok but now not unlocking and start button blinks amber

Installed a Evo one with THAT MAZ3 harness and worked fine for a while. Occasionally would have issue with not doing a standard door unlock from remote. Now never unlocks with standard remote, have to use physical key, and will not push to start, have to hold key up next to button. Push button in car blinks amber. Have changed out key battery many times but no better.
Connectez-vous pour répondre Voir 1 réponse(s)

28/10/2019

 Mazda Mauricio Serrano (130Pts.)

0

Key Fob for Evo ONE

I have purchased the EVO One for my 2019 Mazda CX5. I am planning to use the OEM key fob to turn it on and off. But I was wondering if there's an additional FOB I can purchase to get a longer range. Or if there is any way to get a better range than what I get with the OEM FOB. Thanks!
Connectez-vous pour répondre Voir 1 réponse(s)

14/09/2019

 Mazda Tom Comenole (130Pts.)

0

2016 Mazda CX-9

Installing an Evo One with a THAR-ONE-MAX3. Programming goes through smoothly, decrpyts on the Flashlink fine, re-install, and remote start will not function. I have tried resetting the bypass and decrypting multiple times, checked to insure it is not in valet mode, and re-updated the firmware for both bypass and remote start twice before reinstalling to only get the same result. I have also tried lock, lock, lock and lock, unlock, lock, all times and neither works. I have not hooked up tail lights or pin switch as they are supposed to be controlled by data bus. If this is wrong please let me know.
Connectez-vous pour répondre Voir 1 réponse(s)

09/02/2019

 Mazda Marius pc (230Pts.)

0

2009 Mazda6. Evo one , engine don’t start by remote starter

Hi there, I just installed the fortin one on my 2009 mazda6 with normal key ( not with start push button). I can lock/unlock the doors, I did the bypass with one key and the fortin flashlink 4. Everything seems ok just the engine not start. when I push the button start engine on the fortin remote , the light and inside car led blinks 2 times but the engine not starting. Its not in valet mode, I already checked. Also I tryed to with the key on ON position, leg on the brake, the key near the transmitter, and hit the fortin remote button but nothing happen. If I try 2-3 times , once another, the check engine light start to blink few seconds. On the diagram doesn’t say that I have to cut the yellow wire from fortin module. It’s so soooooo frustrating and hard to make it work........
Connectez-vous pour répondre Voir 0 réponse(s)

28/01/2019

 Mazda Dan G (160Pts.)

0

2016 mazda cx3 starts then shuts off

only after sitting for several hours (overnight) car will remote start normally, then shut right back off. remote start works normally if car hasnt been sitting overnight/8 plus hours
Connectez-vous pour répondre Voir 0 réponse(s)

13/08/2018

 Mazda socalguy (200Pts.)

0

Remote Start Not Working: EVO-ONE & THAR-ONE-MAZ3 on Mazda CX-9 2016

I cannot get the remote start to work using an EVO-ONE with THAR-ONE-MAZ3 harness on a Mazda CX-9 2016. The EVO-ONE has been configured in Remote Starter to enable option 38.5 Lock-Unlock-Lock to remote start and the module flashes blue, 2x blue, then blue and nothing happens afterwards. I do have the module firmware upgraded to 71.46 with options C1 and D2 enabled per the installation guide. Is it possible some of my other settings are not configured correctly?
Connectez-vous pour répondre Voir 1 réponse(s)

06/01/2018

 Mazda nicktagz (280Pts.)

0

CX-3 won't start

After the remote start fails I get 3 red blinks from the module. No tach is the code but I don't know which cable is messed up. I have the evo-all hardware ver 6. Service # 003606005190. Also I'm not sure if I have the correct setttings selected.
Connectez-vous pour répondre Voir 0 réponse(s)

16/11/2017

 Mazda ChrisP (230Pts.)

0

Preferred setup for 2016 Mazda CX-5

Hi, Sorry if this question was answered previously but I'm not seeing my answer. I have a 2016 Mazda CX-5 (push-to-start automatic) and would prefer not to use a seperate fob. • Will any of the options allow for takeover so the car doesn't stop when the door opens? • Which option would allow me to add a mobile (smartphone) solution down the road? • Do any of the options require no cutting of cables in the vehicle (true plug and go)? • Are any functions not available by my using the factory fob alone? • Is there a different start sequence that doesn't sound the horn? My days start early and I don't want my neighbours to hate me. thanks!
Connectez-vous pour répondre Voir 1 réponse(s)

12/11/2017

 Mazda dung vo (190Pts.)

0

install guide for 2017 cx5 evo all THAR-MAZ1 take over

there is a way i can get a diagram because i cant seem to find it. i have a remote starter which is the Encore E7 that i want to connect along with the evo all but there is only 1 takeover install guide but it doesnt have the THAR-MAZ1 in the install. was wondering if i have to tear it apart?
Connectez-vous pour répondre Voir 1 réponse(s)

27/09/2017

 Mazda Christoph Eque (130Pts.)

0

Mazda CX-5 Europa

Hello!
I would like to buy the module EVO-ONE to restart my Mazda CX-5. Does this also work for European vehicles?
Best regards

Connectez-vous pour répondre Voir 1 réponse(s)

12/02/2017

 Mazda Bernard Phillips (200Pts.)

0

2015 Mazda CX-5 will not remote start

Wired and installed EVO ALL according to Guide 62951. I did not connect the park lights. All programming steps worked according to guide. When I attempt to remote start by pushing lock 3X on the fob, the module will light up as follows. The red LED will light up. 2 seconds after the red LED lights up the yellow LED lights up. They both stay on for 8 seonds and then both turn off. The process repeats a second time about 4 seconds after both LEDs turn off. After the second time nothing happens. The blue LED on the module does flash when I hit Lock/Unlock on the fob. I have tried remote starting with the Dark Blue wire for the safety switch grounded and not grounded with no difference. The module has hardware version 6 and firmware update is 71.39. Options C1 and D1 are selected.
Connectez-vous pour répondre Voir 2 réponse(s)

19/01/2017

 Mazda Jerry martin (780Pts.)

0

mazda cx-5 wont remote start blink 9 times

customer had trouble remote starting her car sometimes it started and sometimes didnt when it started it wouldnt stop with remote. She came by garage verify version and remote start had 71.26 on it, replaced it with 71.37 and now its blinking 9 times when remote starting and it doesnt start. Check wiring dont have t harness all wiring seems ok, check with multi-link tool and ignition for remote start comes on but car ignition doesnt.
Connectez-vous pour répondre Voir 1 réponse(s)

21/11/2016

 Mazda Sean ONeill (290Pts.)

1

2014 Mazda CX-5 Automatic - EVO-MAZT1 versus EVO-ONE plus THAR-MAZ1

I want to install a remote start solution in a 2014 Mazda CX-5 automatic. What is the advantage of installing an EVO-ONE with a THAR-MAZ1 harness, versus goning the the EVO-MAZT1 (EVO-ALL based) solution? FYI... Your web site product info seems to be inconsistent when I compare these 2 solutions for the CX-5. In the :Adavanced Features" section of the comparison matrix, it shows EVO-MAZT1 with "Standalone Remote Start" as "yes" but the EVO-ONE as "N/A". And in the "Remote Starters" section further below, it says the exact opposite. Thanks! Sean
Connectez-vous pour répondre Voir 1 réponse(s)

30/03/2016

 Mazda Jerry martin (780Pts.)

0

mazda cx-5 doesnt remote start

installed an evo-one in a cx-5 everything went good done the programmation 1-12 went good done it a second time and i only get a yellow light not the usual red and blue .tried to progarm the blue led and it start to alternate red-yellow-blue then blinks blue like when you program with one key fob.tried to remote start without success park light lights up when trying to start and then turn off and doesnt blink only thing that blinks is the blue led on the rf antenna as it blinks 4 times
Connectez-vous pour répondre Voir 1 réponse(s)

14/02/2016

 Mazda Joshua Swenson (1580Pts.)

0

Any updates to 2009 Mazda 5 install?

I have a 2009 Mazda 5 Sport.  As far as I can tell there is not a 3x Lock option if I want to use my OEM remote.  According to this it appears the EVO-ONE has remote start functionality for my car but the EVO-ALL doesn't?

What would I need to start the car with the EVO-ONE?

And the EVO-ALL could only act as a bypass, correct?

Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer