Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Utilisateur

Bradley Hartman

À rejoins en date due:

Jan. 1, 2021

Points

330

Commentaire(s)

3

Questions votée(s)

0

Réponses votée(s)

3

Votes positifs

0

Votes contre

3

Votes reçus

0

Votes négatifs reçus

0

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

0

Does evo all have to be setup for 3x lock for mycar module to work?

Looking to get Mycar module. I have a 2019 explorer with evo all standalone fort3 harness. I set it up using lock/unlock/lock to remote start. Mycar directions is showing 3x lock for install. Will it work using my configuration? If I have to, I will disable horn honk with lock press with forscan, but I would rather not if possible.

0

Single horn chirp and no start

2019 Ford Explorer Base model key start with EVO ALL standalone. With fort3 harness as well. Running 4.01 firmware, and seemed to be successful programming after I went in with forscan to activate remote start on the BCM and IPC. It goes through the motions after I hit lock/unlock/lock. Red LED comes on, then yellow, then blue flickers with a single horn honk/parking lights flash. It does this again, and then I get 3 red LED blinks, which I know means no tach/no start. Is there any other settings that need to be turned on in forscan? I have a toggle switch instead of door pin. I also tried disabling hood switch in forscan, and the same thing happens.

0

EVO ALL won't recognize keys on 2019 Ford Explorer during programming

Evo all standalone wire to wire with t-harness firmware 71.52(i have also tried 71.49, 4.01, 7.47, and programming related to listed firmwares) I am trying to do 2 key programming. When I get to the step of holding(the folded key) to the ignition, press the button on EVO, nothing happens. Nothing progresses. Any ideas for where I need to look? CAN bus is wired and voltage tested good. Wires were stripped, wrapped, and taped. Module does seem to communicate with vehicle with key fob sending lock/unlock(blue LED lights up) functions, then doing the lock/unlock/lock, it flashes 5 times RED which i know means hood open. Not sure why as the toggle switch has a good ground and is turned off. The toggle is wired into the dark blue A8 wire on the 20 pin connector. Please advise

0

EVO ALL stand alone won't program to my 2019 Ford Explorer

2019 Ford Explorer Base key start, no hood pin, auto trans

I can get the CAN bus to program(I get the proper lights) Can bus voltages checked at 5 pin connector. 

key on.                                Key off

CAN 2 HIGH  2.76V.            2.08V

CAN 2 LOW.   2.24V.            2.08V

CAN 1 HIGH. 2.72V.             0V

CAN 1 LOW.   2.27V.             0V

Firmware is 71.49 as flash link suggests Toggle switch instead of hood pin has good, verified ground EVO ALL won't program my key information. I have gone through the steps prescribed(old method) with putting key in ignition, wait 6 seconds, then putting second key in for 3 seconds. Ignition comes on, but stays on. No blue LED flashing and have to unplug module to turn off. Also tried new method of folding the key in, and placing in front of the ignition, then pressing button on EVO ALL, but nothing happens. Blue and red LEDs stay lit. I am at my wits end. I have been searching all over this forum for the answer, but here I am asking the question. I am not sure which harness I have, but there is a t harness that goes to the ignition barrel, and the 4 CAN hi/lo wires that I stripped wrapped and spliced, and are on the correct wires behind the OBD2 connector. Car was bought new in 2019 with 2 factory keys..

No results

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

Support Technique

Recherchez parmi nos produits les plus populaires et les sujets d'installation disponibles dans notre section Questions et réponses.

En savoir plus
Téléchargez notre application de guides de dépannage étape par étape disponible pour iOS et Android ou parcourez notre version de bureau.

En savoir plus
Accédez à la plus grande base de données de schémas de câblage et de photos en ligne de l'industrie. Un jeton gratuit est fourni dans chaque boîte EVO-SERIES.

En savoir plus
Vous n'avez pas trouvé l'information que vous cherchiez ? Posez-nous une question en remplissant le formulaire de demande de support technique. Un spécialiste produit vous répondra sous peu.

En savoir plus
Des solutions de contrôle à distance et de connectivité à la fine pointe de la technologie au soutien technique haut de gamme, découvrez pourquoi vous devriez choisir les produits Fortin.

En savoir plus

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer