Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

Honda Crv 2017 EXL tailgate problems

Hello. I bought a car in the USA, it arrived to me in Ukraine, and I encountered a problem with the EVO-ONE system Serial number #002B04 051298. Honda CRV 2017 EXL, push and stop system. The car sat for a long time and was transported to Ukraine, and the battery was probably disconnected. Remote start is now working. The car has a keyless entry system. The original remote has a remote start button, I first lock the car, then hold that button for 4 seconds and the car starts. But the problem is this: 1. The motorized trunk opening does not work both when the engine is running and when the engine is stopped, and under security and without security, the trunk lid does not rise or fall, and I cannot do this either from the remote control or from the button in the cabin or from the button on the the door itself. I went to the dealer, there are no errors on the door computer and motors, all fuses and wires are in order. If you open the lock mechanically manually from the passenger compartment, then the door can then be closed using the remote control or any button. But then it won't open. It was also noticed that if you disconnect the battery from the car and connect it back, the door can be opened in any way, either remotely or with a button. But then it also locks. 2. It was also noticed that if, with the car closed, on the outside of the trunk you press and hold the trunk open button several times, the remote start system turns on and the car engine starts. In general, i can now get into the trunk only in two ways, either through the interior, or by disconnecting the battery. Unfortunately, we do not have service stations in Ukraine that have programmers for FORTIN. It turns out that I can only rely on Bypass programming. I will be very grateful for your answer and help!

0

2016 Honda CRV Push Start Takeover

Is there a takeover setting for the 2016 Honda CRV Push Start? After remote start car turns off when door is open. I turned D3 open door shutdown to off. However, still turns off upon opening door. Which leads me to believe there is no takeover feature for this vehicle.

0

Will I be able to connect the compustar ft-alarm-it-kit as my alarm trigger to my evo-one?

I would like to use the compustar alarm it kit since its a all in one sensor. I was not able to source any information on this topic. Thanks.

0

T harnes for evo all 2010 honda crv?

Is there a compatible T harnes for evo-all on a 2010 honda crv?

0

Honda crv 2011

Mon auto démarre bien mais elle s'étein apres 30 seconde tout fonctionne mes porte se débarre mais l auto étein apres 30 seconde environ

18/05/2020

Honda JR (130Pts.)

0

EVO One Module Not powering up after Parking Lights, horn and Door Lock Connection

I just purchased an EVO one with a THAR-ONE-HON1 T-harness for a 2011 Honda CRV. I successfully programmed the module prior to installing it in the vehicle using the Fortin Flashlink V4. I installed the T-Harness onto the vehicle without connecting any of the horn, parking lights or door lock provisions at first, so that I can perform the key bypass procedure. I was able to set this up successfully with no issues. I even tested that the vehicle would be able to be started via the 3x lock procedure. All was perfect.

 

I then proceeded to connect the parking light connection along with the horn and door lock connections. All of the instructions were used based off of the 57711 guide. I also used the activation code for the wirecolor website prior to splicing any connections. I also verified with the colors with my service manual and all was good. After splicing into the factory connections for the horn, parking lights and the door lock, I proceeded to attempt the remote start procedure and the vehicle. The parking lights and horn worked flawlessly, the door lock however would not unlock. I had to manually open the door to unlock it. I then proceeded to turn off the vehicle, I figured maybe it was a glitch.

 

I then proceeded to attempt to remote start the vehicle again and this time the vehicle would not start. The module would not even light up, no color would show. The module seems to be dead now. I have verified all connections twice before splicing into the factory harness and then proceeded to verify another two times afterwards just to make sure that I did not accidentally wire anything incorrently. Everything is connected exactly as the instructions show. I'm not sure exactly what could've caused the module to stop working with everything being connected properly. Please help. Thank you!

0

2008 Honda CRV, blue light flashing slowly after programming

Following guide #57701 I have installed an EVO-ONE service no:002b07 184652 into a 2008 Honda CRV. Programming steps 1-5 appear to go fine, at step 6 when i turn off the ignition the blue light starts flashing slowly and does not turn off. I've verified wire connections and unplugged the module and attempted to start. The security light flashes and will not start. Any idea what I have done wrong?

12/02/2018

Honda Nam Ly (350Pts.)

0

Drone mobile timed out with Evo-one. No communication.

0

Immobilizer and evo-start not programming

When I first programed the immobilizer thru DCryptor it all went fine and was working. I tried to program my evo-start, after step G (press and release brake pedal) the antenna LED never flash blue. Tried like 20 times without any luck, when I send a request with my phone the antenna blink green fast than amber for 2 seconds or if I press and hold the button on the antenna the LED turn on green than flash 7x amber. Both code have in common that it may not using the good protocol. Now it will crank but no start, I tried redo the DCryptor process, did it 10x every step looks good but I always get a message saying the immobilizer data is incomplete. Now my question is how do I get the immobilizer to work again and the Evo-start. I don`t know if the module is bad or what but I`m having hard time to program it since the beginning, sometime it work next time it won`t. It my first Fortin, I did few Autostart before. It on a 2016 Honda CRV PTS and it has the T-harness. Thank you

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue