Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

Genesis G80 support?

Will you guys be adding coverage for a 2017/2018 Genesis G80?

0

programation

bonjour par érreur jai appuyé sur la touche Fonction et démarrage et maintenent quand je démarre lauto avec le démarreur et que je déverrouille mes portières le clason bip 3 fois. Sur la manette du démarreur il avait un signal clinote vert avec des bip et maintenant jai une del rouge et un son grave.Comme remettre avec la programation du débu svp

2

2015 Hyundai Genesis PTS Evo-One doesn't start

I used guide 17323 revision 20140804 to wire up a 2015 Hyundai Genesis PTS to and EVO-One. I have programmed the EVO-One and it responds as the directions say. I have oem remote monitoring on, when I lock the doors three times, I get a blue blink every time I hit the lock button, on the third press the parking lights come on, the doors unlock, the car's dash screen comes on but it doesn't start. The middle LED on the EVO-One is lit orange and after about 5 seconds it locks and unlocks the doors, then about 5 seconds later it locks all the doors and the middle LED shuts off. If I had to guess I would say that the starter out is either not sending the signal or the starter+ is not hooked up correctly? I have it hooked to the brown orange wire in the loom indicated on the wiring diagram but there are a ton of wires there. What else can I do to troubleshoot? I am running firmware 76.16 with C1, D1, D1.6, D2 and D6 turned on

31/03/2014

Hyundai (Pts.)

1

2014 Hyndai Genesis Sedan PTS (Dec2012build) Programming/ Car wont take over?

Hi Fortin, Car remote starts but vehicle does not take over after hitting PTS button twice. I noticed when i was programming the evo all and the step where it says turn on/run then blue led will blink 10x to show key bypassed but the next step where blue and red will blink 10x to confirm brake and tach is programmed does not happen. The last step i get is the blue blinking and thats it. Never goes to blue and red? Door locks, trunk,and RS do work fine. Thank you, Ankur104

22/03/2014

Hyundai (Pts.)

2

2013 Hyndai Genesis PTS - Does not have PCM in location for CAN/Keysense/Ignition..

I am installing a Evo ALL stand alone on a 2013 Hyndai Genesis Sedan Push-To-Start. I have looked extremely carefully all over and there is no PCM for the white 20pin connector needed to connect Can HIGH/LOW, Keysense, and Ignition wires i need according to this diagram http://ifar.ca/download/9641/stand_alone_evo-all_hyundai_kia.rev-20130604.pdf I am using Connection 3 and this car does not have the connector or module for Picture reference #1. It looks like there is a spot there for the module but this car is did not come with one. I need wiring diagram for those 4 wires. Please let me know ASAP. Thank you A.G.

1

We have a 2013 PTS Genesis Sedan built in Sept 2012, should we use the 2012 wiring schematics?

We have a 2013 PTS Genesis Sedan built in Sept 2012, should we use the 2012 wiring schematics?

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue