Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

07/12/2023

 Subaru kstatus (180Pts.)

0

2022 Subaru WRX, Manual Transmission, Evo-One, THAR-SUB4, RFK3641, Ready-mode not activating

Car = 2022 Subaru WRX, Manual Transmission, Push-to-start I have programmed, decrypted, and installed an EVO-One using the THAR-SUB4 Harness and an RFK3641 rf kit. When I try to enable the ready mode, the car is not remote starting. I have been following the procedure to activate: Car is running, put in neutral, press foot brake, pull hand brake, release foot brake, here is where it gets weird. According to the instructions I should now press and hold the start button for 3 seconds, but before I get a chance to do that the car flashes the lights 3 times. When I press and hold the start button for 3 seconds nothing happens. I leave the car running, get out, the car automatically shuts off and locks the doors. When I go to remote start it, the lights flash 3 times and nothing happens. I have tried doing this same thing with and without holding the start button for 3 seconds before exiting. I have also tried pushing the start button on the car before exiting (similar to "removing" the key), but the car immediately shuts off. Looking for some assistance, thanks!
Login to reply View 2 answer(s)

14/03/2021

 Subaru losmt2 (350Pts.)

0

THAR-ONE-SUB2 & EVO ONE on 2020 Subaru WRX PTS

I have installed the THAR-ONE-SUB2 in my US WRX per the instruction guide, page page 7/11 T-Harness - Automatic & Manual Transmission 
https://cdn02.fortin.ca/download/98951/evo-one_ig_rto_bi_sub2_wrx_2019_pts_b_98951.pdf

ASK:
1.) Why is the car not starting with the Yellow/Red and Yellow/Green separeted per the installation guide
2.) Does my US WRX have to follow the Canadian Vehicle steps, if yes why and if no what is the difference
 

Installation was simple as mainly 2 connectors and areplug N play. I master reset my Evo One, flashed the 2020 WRX firmware and follow the programming steps on page 8/11. When I get to step 5 to start the car, the car starts and shuts off immidiately, eventually not even turning the starter. The lights on the Evo One stay solid for Red and Blue and programming does not complete to follow up on the Dcryptor part. After a little troubleshooting I found that I can get the car to start if I reconnect the Yellow/Red and Yellow/Green wires I cut eariler making the car at least drivable again.

 

Login to reply View 1 answer(s)

15/09/2020

 Subaru Jesse Kingsbury (220Pts.)

0

2018 Subaru WRX PTS Manual Transmission

Hello, I'm looking for a T-Harness installation for a 2018 Subaru WRX PTS with manual transmission. Are you guys gonna have anything for this anytime soon??
Login to reply View 1 answer(s)

04/11/2016

 Subaru Brian Ho (190Pts.)

0

Drone Mobile Issue

I have a MY15 Subaru WRX Limited 6 speed and i had the 3 key start working for the car. I also have the drone mobile that i added to the system. From the research I ddi, i need to flash the firmware to 0.5 for the starter optoins. Now after flashing, its seems i cannot start my manual car with tthe 3 key clicks, turbo timer, or control the functions. It wont lock , open trunk remote start... i looiked at the hardware and after flashing, the options for the remote start disapeared, what should i do?
Login to reply View 1 answer(s)

02/11/2016

 Subaru Brian Ho (190Pts.)

0

Fortin Evo One red and yellow flashing

I have a evo one and using a t-harness for my 2015 Subaru WRX Limited Manual transmission. I go the wires all hooked and Im not sure if I was able to get the initial programing done correctly. I was doing this at work and needed to get home despite being unsure of it being programed properly, started my car and drove home. I tried doing the initial setup with the red and blue light being solid. Now the module has a solid blue while blinking red and yellow at the same time. Is this a concern ? What should I do if it's not correctly setup.
Login to reply View 2 answer(s)

18/12/2013

 Subaru Marco Kwan (140Pts.)

1

2014 Subaru WRX supported?

Is the 2014 Subaru WRX supported by the Evo-All? I saw that the 2013 is, and considering there aren't any changes between models, I was wondering if I could use this for an install. Thanks
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue