Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

15/05/2019

 Subaru Edrice Iraola (1090Pts.)

0

Tele-connect + horn wire??

Hi I have a 2017 Subaru Legacy(standard key) with Evo-One and I’m going to install the Tele-connect device and on the manual step2 to connect yellow wire to positive horn wire but the evo-one is already connected to the negative horn wire, do I still need to connect the yellow wire from the tele-connect to positive horn wire? i tried searching where/what color my cars positive horn wire but couldn’t find it. Also if I connected the horn wire from tele-connect do I need to disconnect the horn wire from EVO-One? thank you
Login to reply View 1 answer(s)

27/12/2018

 Toyota FancyChancie (140Pts.)

0

MyCar Telematics starts then turns off after a few seconds

Vehicle: 2011 Toyota Corolla S (G-Key), manufactured in CAN.

Evo-One w/T-harness installed and working properly using OEM remote (3x lock to start).

 

When trying to start vehicle via the MyCar app, the engine will start and as soon as the doors auto lock the engine will shut off.

 

I have installed the MyCar Controls telematics unit based on the guide here: http://cdn02.fortin.ca/download/64631/autolink-install-guide-64631.pdf#page9

I used the HRN-LLRS-01 connector as instructed.

“Fortin 2” selected in RF section of configuration tab in FlashLink Manager.

MyCar Controls app Device Protocol: Fortin

 

Please help!

Login to reply View 1 answer(s)

17/03/2018

 RF-Kits (Pts.)

3

Cannot Learn MyCar Telematics Module - Evo-One

I am trying to learn/teach the Evo-One the MyCar Telematics module. I have followed the directions and preconfigured the Evo with the Fortin 2 option. I cannot get the Evo into programming mode. I turn the Ignition to ON hold the button (next to loop) on the Evo for 5+ seconds as the instructions say, but the led never changes to red and remains amber. Any suggestions? I should also note that my install was done using all T-Harnesses so I know I don't have any wiring issues. I tested the Evo for functionality before moving onto MyCar install as well and everything works great. Here is the instructions: http://www.crimestopper.com/cstech/library/security/security_systems/remote_start/mycar_installation_guide_20171109.pdf
Login to reply View 0 answer(s)

24/11/2017

 Infiniti Angel Sanchez (310Pts.)

0

Crimestopper TELE-connect not working

Hi there, I'm trying to install the Tele-connect to an evo-one using the T-harness on a 2006 Infiniti G35x with intelligent-Key. I'm using Guide # 33131 I've enabled the following so far but no luck.

32. mode 3

2. mode 3

8. mode 2

RF Kit Compatible has been set to "Fortin 2"

 

Login to reply View 1 answer(s)

11/04/2017

 Honda Walter Gonzalez (220Pts.)

0

EVO- ONE and Crimestopper TELE-Connect

Hi, i just installed teh evo one with t harness on 2012 honda civic oem key. i followed everything to the tee and got the evo one to work properly as well as the remote start. I added the TELE-connect Crimestopper and when i go to learn the telematics module to the evo one or vice versa, the installation guide is asking to place the key in the ON position to show the Yellow Led on EVO one. which it does. the next step is to hold the button down for 5 seconds till the red led on the evo one turns on. this part does not happen on the evo one while the key in ignition is in the ON position. i cant get pas that part of the learning process so i cant proceed. i did flash the evo one for configurations to fortin 2 as written on the tele-connect installation guide. i did it under Bypass toggle and remote start toggle. the firmware for remote start is updated to lates firmware and the bypass mode is at 73. 24 as directed by the instructions. ive tried trouble shooting but no luck. hopefully someone can help.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue