Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

04/12/2019

 Toyota John Klimek (430Pts.)

0

Where to install remote starter antenna? Under rear view mirror/camera?

I have a 2018 Toyota RAV4 Hybrid and I've successfully installed the EVO-ONE and it works perfect.  I'm now adding an RFK912 RF kit.

 

Where is the best place to install the antenna?

 

Usually it's placed at the center of the windshield behind the rear view mirror, but the RAV4 has a camera/radar box there.  Can I safely remove the box and install the antenna inside it?  Should I place the antenna outside (and next to) the box?

 

Also, is it easy to remove the rubber around the door frame to route the antenna wire from the main ECU area (where the remote starter is) up to the rear view mirror area?

 

Thanks for any help!

Login to reply View 1 answer(s)

23/11/2019

 Toyota John Klimek (430Pts.)

0

Automatic lights do not work after install on 2018 RAV4

I've just finished installing the wiring on my 2018 RAV4 XLE Hybrid and now the automatic lights do not work.

 

NOTE: I've only connected the wires and the EVO-ONE is not connected yet.

 

I'm using the Fortin THAR-TOY6 harness and I've connected everything exactly as described in the manual:

 

1) Purple wire to (+) STARTER.  (soldered connection)
2) White/Black wire to (-) START/STOP.  (soldered connection)
3) +12V and GND wired to OBD2 per manual.  (used Posi-Tap connectors;  there is absolutely no way to pull OBD2 connector far enough out to solder wires behind connector)
4) "A" harness/passthrough connected to Main Body ECU.

 

I do not have an EVO-ONE yet but I wanted to finish the wiring.  All car functions still work properly except the automatic lights.

 

What can I check to see why they are not working?  I was extremely careful during installation and can't imagine why it's not working except that I don't have the EVO-ONE installed yet.

 

Login to reply View 1 answer(s)

12/10/2017

 Toyota ANTHONY LE SAOUT (130Pts.)

0

connecteur bouton start Toyota RAV4 hybride 2017

Bonjour, pouvez-vous me dire comment accéder au connecteur du bouton poussoir start du RAV4 hybride ? merci
Login to reply View 2 answer(s)

08/10/2016

 Toyota James Larsen (200Pts.)

0

Dome lights no longer working following remote starter installation

Hello there 

 

After properly installing the EVO-ALL standalone remote starter on a RAV4 Hybrid (2016, PTS) I have recently noticed that the cabin dome lights are not being lit when any door is opened. I have checked the fuses (OK), and the lights themselves are working just fine when toggled on/off manually for both front/rear in the cabin.

 

What do you recommend that should be done to the EVO-ALL installation for the dome lights to function again for this vehicle without removing the remote starter of course?

 

The days are getting darker up north and the dome lights become indispensable as we progress into winter.

 

Thanks!

Login to reply View 1 answer(s)

01/09/2016

 Toyota James Larsen (200Pts.)

0

Colors and numbers of wires in 30-pin connector in vehicle do not match with details in EVO-ALL installation guide!

Hi

 

I am attempting to install an EVO-ALL stand alone remote starter on a Toyota RAV4 Hybrid (2016, push-to-start). Until I got to the 30-pin connector the installation proceeded smoothly as described in this guide: http://fortin.ca/en/download/58691/58691.pdf

 

As you can see from my attached photos the wires on the 30-pin connector in question look different than the one pictured in the guide downloaded from fortin.ca ('58691.pdf'). A couple of wires do not exist in my vehicle (among others: blue and red wires for tapping into RX and TX respectively).

 

Do you have any recommendations on how I can continue and complete the installation?

 

Thanks.

 

Link to previously attached photos: https://jimlarsen.ocloud.de/index.php/s/HrIMS9quD2v6ewg

Login to reply View 2 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue