Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

17/01/2017

 Toyota Le Dang (130Pts.)

0

2010 Toyota Venza PTS EVO-ALL stand alone

Hi, I'm at the programming procedure, after plug in the remaining connectors. I Press the Push-to-Start twice. I only get a RED LED flashing rapidly and constantly. But if I push the programming button, it will flash the BLUE LED rapidly. Then push the programming button again will flash the BLUE and YELLOW. Finish the programming but lock 3x does not do anything. I'm on firmware 79.39 with no T-harness Thanks
Login to reply View 1 answer(s)

15/02/2016

 Toyota bao dinh (740Pts.)

0

toyota venza 2015 remote start

i installed a viper remote start system for my customer to a toyota venza 2015 with evo-all , i done every thing exactly the same as the evo-all installation diagram , and 2 month later the BCM on this car burn out and the dealership said the BCM get overloaded by the remote start system , the remote starter power wire i connect to the Blue 12v wire at the ignition harness , and another thing is this car also have an aftermarket sound system , 1 bass amp and 1 12" sub , may be my customer running the car by the remote start and listen to music ... will the bcm burn out if remote start and listen to music because of not enough power ?
Login to reply View 1 answer(s)

07/12/2014

 Toyota t p (300Pts.)

0

Will Revision 20110506 work will 2013 and later model, or 2015 Lexus RX 350?

Hi, thank you for you quick response. Fist, the link enclosed was in French. My French is not very good. Could please kindly point me to an English equivalent copy? Second, with my limited French knowledge, this revision was written for 2009-2011 model year Venza with Push to Start. Would the same wiring work for 2012 and later model year Venza? Third, if a similar revision available for 2015 Lexus RX 350, could you please also provide. Lastly, do you have an authorize local distributor in Dallas, Texas, US, wiho can flash/prepare/intall the EVO-ALL? Much appreciate for your support and time
Login to reply View 1 answer(s)

06/12/2014

 Toyota t p (300Pts.)

0

Could 2013 Toyota Venza PTS install with Viper 5702 remote keyless entry have takeover option

Hi, My Toyota Venza currently have OEM remote starter WITHOUT able to takeover. (i.e. when I unlock or open the car, the engine shut down) Is there anyway to install a Fortin module so that I can use the OEM key (or an aftermarket remote starter such as Viper 5702) to start the car but CAN also takeover (i.e. the engine not shut down wihen I unlock or open the door) Please advise Thanks TP
Login to reply View 1 answer(s)

12/01/2014

 Toyota William2 (1630Pts.)

2

2010 toyota venza with PTS will not start using compustar cm6200 and evo all

Evo All service# 001A06282907    Firmware 4.18

I installed the system using guide#8601. The evo all programed fine, the remotes, door lock and trunk work fine.

The tach and hood wires are not required with the evo all per fortin's guide.

I am having problems with the remote start.

I followed the fortin guide and everything was connected as instructed.

 

I press the remote start button on the remote and the car receives the signal to start. It flashes twice and turns on the dash cluster like is going to crank but it doesn't even try to crank. The odd thing is it turns the dash off and then on twice before giving up on the remote start process.  Is like it tries 3 times to start but doesn't crank.

 

Any ideas? 

 

I tried learning the tach, going tachless and changing the crank time but still did the same. 

 

UPDATE AS OF JAN. 12TH 2014:

I reseted the evo all and reprogrammed. Now the car cranks for 0.5 sec but does not start. Then it does the "dash on and off"3 times again. The remote flashes 3 times after failing to start(the error code for 3 flashes is "doors open(manual trasmissions only) but I cut the green loop inside the CM6200 module to make it automatic.

I tried increasing the cranking time to 1 and 1.5 sec. but still will not start and it only cranks for like 0.5 secs.

I did the tach learn process and was not succesful.

I think this is related to the tach and door pin wires not being connected as instructed in the guide, could it be?

Note: when I start the car with the key the yellow led on the evo all is the one on.

 

Thank you

Login to reply View 1 answer(s)

14/01/2014

 Toyota Ten Ten (250Pts.)

1

EVO-ALL TOYOTA VENZA 2010 PTS Not remote start.

Updated firmware (79.00), the remote run included ...
Login to reply View 1 answer(s)

11/01/2014

 Toyota Ten Ten (250Pts.)

2

EVO-ALL TOYOTA VENZA 2010 PTS Not remote start.

Hello! EVO-ALL TOYOTA VENZA 2010 PTS I did everything according to the guide # 8611, block programmed. Then, when I press the "lock" button 3 times on the key, the ignition turns on but the car will not start. Starter does not turn.  What could be wrong?  Where to connect the wire yellow / black (A13)? Regards, Konstantin.
Login to reply View 2 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue