Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

19/01/2024

 Ford Ramiro86 (300Pts.)

0

Evo All as bypass on an Avital 4105L

I made the entire connection of the "Evo all" as a bypass on an Avital 4105L and it doesn't work, I don't know what could be wrong, I did the installation according to the guide.
Login to reply View 1 answer(s)

13/01/2024

 Ford Ramiro86 (300Pts.)

1

Evo All as bypass on an Avital 4105L

I tried using Evo All as a bypass on an Avital 4105L and tried to start my 2005 F-150 with the oem control and it didn't start, only started with the Avital control
Login to reply View 2 answer(s)

05/12/2023

 Ford Enrico Camia (240Pts.)

0

D2D or W2W Fortin EVO All with FORT1 T-Harness and AVITAL 4105L for 2011 F-150

Hi, I purchased the THAR-FORT1 Kit which comes with the EVO ALL and FORT1 T-Harness. I also purchased the FlashLink updater and will set the EVO ALL to D2D. I would like to pair all of this with an Avital 4015L remote starter for my 2011 F-150 (I do not want to use the factory remote start protocol as my truck doesn't have power locks). I would like to only use the D2D cable to connect to the Avital 4015L in order to cut down on wire clutter. I would like to know if the D2D cable is the only cable I need to connect between the these two. I was looking at the wiring diagram for the EVO ALL with the FORT1 T-Harness and on the left side of the remote starter every cable is optional if D2D is used but on the right side there is parking lights which I don't care for so I wont be hooking up and Ignition. Doesn't the ignition communicate through D2D? https://fortin.ca/download/94881/EVO-ALL_IG_RTA_BI_FOR-FSERIES-2011-2016_KEY80bits_D_94881.pdf Wanted to know if I am on the right track here before I start the install. Thanks!
Login to reply View 1 answer(s)

02/01/2019

 Ford Colin Beech (130Pts.)

0

Connecting Python 4806p to Evo-Fort 4 T harness and Evo-All?

Hello! I purchased on Evo-Fort4 that I am going to attempt to install on a 2017 Ford Escape with standard key. I'd like to use the T-harness to perform all the wiring, using connection points 1 - 6 in the install guide, and then manually making the 22 wire connections. The plan is then to connect the Evo All to the Python 4806p using the D2D connection; I have updated the Evo All firmware, and activated the F3 option. Here are my questions/problems: 1) I can't seem to connect the D2D from the Evo to the Python - the Python D2D interface is a larger plug, and neither my T-harness with the Evo or included with the python will fit. How to connect? 2) Is it reasonable to assume that the *ONLY* connection the Python 4806p will need is the D2D connection, since all power and logic will be piggybacking off of the Evo unit? In which the Python truly just is the remote starter?
Login to reply View 1 answer(s)

07/03/2016

 Ford Joe Allison (220Pts.)

0

2013 F150 EVO-ALL, added SmartStart but lock/unlock doesn't work

Everything works great using the fob itself (OEM) and I have it setup for lock-unlock-lock SmartStart VSM300 installed today, flashed to activate RF unit in EVO-ALL. SmartStart unit starts the truck fine, but the lock/unlock does not work through the app/smartstart. it appears to "send" the command for the lock/unlock, but it does not lock/unlock without doing it on the OEM FOB. Any thoughts? That said, could this be because I DO NOT have the wires tapped at the BCM for lock, unlock and the door pin? It didn't say they were required connections on the basic (use OEM fob) install. However, are they required to get the SmartStart/RF unit to lock/unlock the truck? Joe
Login to reply View 1 answer(s)

16/12/2014

 Ford Raymond Kazmierczak (1200Pts.)

1

EVo won't bypass key unless purple white wire grounded for split second

2012 Ford Edge 80bit key. Installed viper smart start and remote start. Had to do w2w because of smart start module interfering with Evo-all. Car starts in d2d mode without smart start module. When in w2w I have to ground purple/white wire for one second after initialization and release before it starts. Now the guide mentions grounding unlock wire and hooking another unlock wire to purple white but that doesn't work. Any ideas?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue