Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

Ready to start

Bonjour j’ai un Honda civic si 2015 et je voudrais savoir c’est quoi la séquence pour activer le prêt à démarrer. Mon evo one est le 002B07071941. Merci bien !!

0

2018 Civic Si No ready mode (RF 442)

Just installed an evo one and Rf-442 kit on my 2018 PTS civic. Used the Hon7 harness, so I had to do the interruption at the steering lock and tap into the clutch wire. Also ran the dcrytor process when the guide prompted. Also worth noting that the yellow light is lit when the ignition is on. Whenever I try to remote start the car with either remote, the parking lights blink 3 times indicating that the car isn't in ready mode. When I programmed the module using wizard mode, I made sure to select the middle sequence (car in neutral, foot on brake, park brake...etc), but when I leave the car, it continues running and says that the key fob is not detected on the dash. Made sure that valet mode was disabled via the rf antenna. All of the other functions of the rf remote seem functional minus the remote start. Im guessing this is a programming error, any help would be appreciated

0

Civic 16' (Manual) w/FTX64 2W - Ready mode no longer saving my dashboard preferences

Hi, I Have a Honda Civic 2016 (Manual). I bought an aftermarket remote starter in 2019. The controller is an FTX64 2W. I used it without issues up until this winter. I would stop the car, leav it in neutral put the park brake on, and then press the ON button on the controller to start the Ready Mode. With the exception of the rear-window defroster which never worked, any preferences that I had on my dashboard would turn on when I activated the remote start later on (seat heaters, front window defroster, temperature, etc). This winter I noticed that when I get out of the car after activating my ready mode (after about 3-5s) the remote emits a red light and makes the descending noise (same on as if I remote stopped the car). When I then remote start the car, it will turn on, but none of the preferences on my dashboard will be on (cold seats, no defroster, no temperature, etc). The only thing that has changed is that one of the remotes (I have two) is dead. I will be replacing the batteries this week and trying that one out too. Anyone know what could be causing this? As I said, it worked well up until this winter and then stopped out of nowhere.

0

Remote start not working and door chimes with lights off!?

Everything was working after Rob helped me out programming the remote start side of the unit for manual transmission. Was cleaning up the install and must have unplugged the unit the wrong way. Now the car won’t crank again, and ready mode works up until the last step which is relocking the car after door closes and car shuts down. I have relock enabled on both sides of the unit, tried reflashing and changing different options with no luck. On top of that now my door chimes with the parking lights hooked up and it didn’t do that before and all my lights are off. The headlights don’t give any diagnostic flashes either. Using t-harness and correct guide. 

 

Thanks

0

Ready Mode Disabled - Manual Install

Trying to install my remote start on a 2017 Civic manual key start. I have both t-harness installed, parking lights, horn and clutch tapped. The module programmed the decryptor fine. Ive selected the recommended options in flashlink... Go to remote start and im getting the 3 flash Ready Mode disabled... Trying to find out what the exact procedure is to enter ready mode but im having zero luck finding any information... Any help would be great! Thanks!

0

Manual Transmission Ready Mode

2013 Honda Accord Standard Key w/ Manual Transmission I haven't gotten ready mode to work, or I'm not understanding. There's no documentation on it in the manuals. If I press the brake pedal, pull the parking brake, then release the brake pedal the relays in the unit click and I am able to remove the key from the ignition and the engine is still running. However when I open the door to get out, the engine stops and the unit shuts down and then I can't remote start.

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue