Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

19/07/2018

 Jeep jeff sawicki (240Pts.)

0

Evo All alarm settings

I have a 2015 Jeep Jk with no power locks, so I have no factory alarm. I am using an RF kit to remote start. I see the evo-all has an alarm function, is there a way to have the horn sound if a door is opened? If so what settings or accessories do I need? Thank you It appears the alarm function is not working at all
Login to reply View 1 answer(s)

02/07/2018

 Jeep david smith2 (160Pts.)

0

hood trigger and constant horn

hooked up my evo all. with hood trigger, valet, and proximity sensor. I am using my horn as the alarm and hooked up the relay. everything works fine when triggered. except when i tested the hood trigger the horn honked once then did a continuous horn. it would not shut off with any of the buttons on the key. i had to disconnect the evo-all to shut it off. i connected the hood pin to the dk blue trigger. what could be the issue
Login to reply View 1 answer(s)

16/06/2018

 Jeep david smith2 (160Pts.)

0

extra sensors on evo all

have an evo-chrt5 on the way. also installing a proximity sensor DEI 508d. i have a 2017 jeep wrangler jku with factory alarm i will be using the evo for remote start. can i set up the evo alarm to active and then only use it for the proximity sensor? will that mess with my factory alarm? I will be using a DEI 508d proximity. since i don't have data-link can i use the Ground (b4) and positive (b3) from the data link wires (that would be unused). then hook up the trigger to (a3) dual stage trigger, purple/white. any help you can provide to make this as much PnP as possible will be appreciatd
Login to reply View 1 answer(s)

10/02/2018

 Jeep netrrhexis (130Pts.)

0

EVO-ALL and Jeep Commander CAN BUS

Does the current firmware for the EVO-ALL read the CAN-BUS for door status on a 2008 Jeep Commander Sport? I currently own the EVO-ALL with THAR-CHAR4 for my Commander. The EVO-ALL is currently configured and function nicely. All options work (ex. remote start, alarm, parking lights, horn/siren). The Commander has no factory alarm. If I arm the EVO-ALL I can open ANY door and the siren will not sound. My wait time is 60secs. I know the alarm is armed because if I attempt to turn over the ignition the alarm sounds and the key sentry flashes as expected. Another question is have you actually had a chance to test the CAN BUS High and Low on this vehicle? I personally don't think the current firmware is allowing the EVO-ALL to detect the doors on the network. In relations to the alarm and doors I have played with Option G4. The option works on firmware ver. 7.34 but not on 7.22. However 7.22 is the only version that allows the alarm to work! P.S. I also purchased an EVO-ONE. Do you think the EVO-ONE would do a better job of detecting the doors on the CAN BUS? OPTIONS ACTIVATED: C1, D1, G
Login to reply View 0 answer(s)

06/01/2018

 Jeep Bryan Richardson (130Pts.)

0

How can I add siren and proximity/shock to my evo all

I’ve searched the support section, I have read guide 16221. I want to add a siren with warning chirp and alarm siren and proximity/shock sensor to my Jeep Wrangler using evo only. Please advise Parts needed, preferably Fortin brand. And how to do it. 16221 as well as the install instructions for my CHRT5. Please help, anyone in NC I will come to you for help.
Login to reply View 1 answer(s)

15/10/2017

 Jeep Mark Jenks (180Pts.)

0

Factory alarm isn't disabling when using RF Extender

I've had the EVO-ALL and T-Harness installed in my 2008 Jeep Wrangler (Standard key) for a few years now and it has worked without issues. It works with the factory remote (3 lock to start, 3 lock to stop). It is setup to unlock/lock/relock when remote starting, and handles the factory alarm the like it is supposed to. I have added a Axxess AX-RF2 2 to the EVO-ALL and setup all of the RF options using my Flash Link. I am using the 4 Pin D2d Data Cable Y Splitter. Connected wires are the Yellow, and brown/white running lights. When I use the RF remote, it will lock, unlock, start and stop, but it will not shut off the factory alarm. So it will trip the alarm every time. I've been through just about every option in Flash Link and and can't get it to disable the alarm with the RF. Even with the RF, the factory remote continues to work without issues.
Login to reply View 2 answer(s)

26/03/2017

 Jeep Ahmed Hassoun (240Pts.)

0

hazard lamp and horn with remote start

hi guys : I have jeep grand cherokee 2013 push to start and install fortin thar-chr4 when i left vehicle more than 5 minute and remote start it it was sounding horn and hazard lamp and not stopping just with unlock my car with FOBIK i was update my device to 74.30 and reprogramming my thar-chr4 and same problim note : for second time if i start vehicle with remote start system no problem found the problem appeared just when i left vehicle more than 5 minute any help found Best regard Ahmed Hassoun
Login to reply View 1 answer(s)

25/12/2016

 Jeep daniel adams (160Pts.)

0

Factory alarm goes off after starting.

Factory alarm goes off after 3x start. Can i disable this?Can i disable all the chirps + alram?
Login to reply View 1 answer(s)

19/03/2016

 Jeep KOZ (750Pts.)

0

08 Jeep Gr Cherokee Diesel - alarm goes off on second start.

2008 Jeep Grand Cherokee - EVO-ALL standalone First cycle of RS with 3xlock works fine. If runtime expires or is canceled the second cycle sets off the factory alarm. Option D2 is on - but acts funny. Unstead of just a single unlock before RS, it unlocks then locks immediately. After key take over, drive and shut down, EVO still relocks/rearms doors. I've downgraded several firmware back to .14 but no change. Unit programs fine etc.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue