English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

13/04/2024

 Toyota Christian Gomez (190Pts.)

0

MyCar will not start 2013 Toyota sienna! Tried everything!!

I have looked at all the question and answers with no luck. I update the firmware on the Evo-one, re-programmed every way possible with different firmware’s, re-programmed the mycar module, I’ve used with and without the little harness that comes with the mycar module, see if the Evo receives a lock/unlock signal while on (nothing), checked if the module is plugged in the right slot. I send the signal from the mycar app, turns green and then red for every option. The app shows signal, battery voltage, gps location, but it won’t accept any command. Please help!! (Can it be a defective device?) It worked before and all of a sudden stopped working.
Connectez-vous pour répondre Voir 1 réponse(s)

25/11/2023

 Toyota KIEN MACH (210Pts.)

0

2011 Sienna crank, no start when COLD

Hi support team, My 2011 Sienna G-key start all OK in summer, but it doesn't work when WINTER is coming. S/N 002B04 241048 connected by THAR-ONE-TOY9 (just plug and play). I did connect 2 wires for sliding doors by soldering and crimper (no T-taps). Already upgrade to latest firmware. Tried TACHNESS ONLY but no hope, still CRANK but NO START. I'm connect with RFK442 remote. It happened to me last year, same issue. Work fine in the summer but when it's cold out there, the vehicle just CRANK NO START. When I get into the vehicle and remote start it, leave the key next to the key cylinder, it start right up every single time. Moreover, I've re-checked the wiring connection. There are "CUT" at the SILL data (D4&D6) and the AUTOLIGHT (D1&D3). Do I need to do anything about these "CUTs" when I'm using THARTOY9? Thank in advance for your support.
Connectez-vous pour répondre Voir 1 réponse(s)

09/11/2023

 Toyota u2kstudio (130Pts.)

0

sienna 2021 + evo one + evo start lte = power sliding door control possible?

using the evo-one model. Is it possible to control the power sliding door on the sienna 2021 model with evo-start lte?
Connectez-vous pour répondre Voir 1 réponse(s)

16/06/2023

 Toyota Gerry Gao (190Pts.)

0

3-locks-to-start stopped working after module flashing / added RF kit

Hi,

My evo-all used to working with the OEM key 3-locks-to-start before.

Then I bought the RM 942 RF KIT.

Flashed the evo-all to 78.70, and the antenna to 1.05 already.

I flashed my evo-all to match my vehicle: * Toyota Sienna 2020 * Standalone installation * Standard connection * push to start * No alarm     Enabled the H&H2 option and paired the RF kit keys successfully, with the hlpe from https://www.fortin.ca/en/qa/121700/rm-942-buttons-have-wrong-functions

Followed the DCRYPTOR PROGRAMMING PROCEDURE. All leds are off at step 5 indicating it's already programmed.

After all these, it seems everything are connected and paired correctly. The lock/unlock buttons on the RF kit work properly.

 

BUT neither OEM key 3 locks nor RF kit key remote start ([+] + lock) could remote start the car. After pressing the OEM key 3 locks, I can hear the evo-all or some car electric component making the small clicking sounds, and the car turn signal lisghts had a couple of follow-up flashing, which seems to me like the evo-all is indeed carrying out the remote start procudre. But car does nothing, no cranking sound at all.

 

Did I miss anything again?

 

One weird thing to me is that I think I installed my evo-all with a T-harness, but in the Flash Manager software, after I select TOYOTA, SIENNA 2020, PUSH-TO-START, STANDALONE, there is only STANDARD CONNECT option but on T-HARNESS CONNECTION option in the connection type selector. Is this the problem?

 

Thanks,

Gerry

 

Connectez-vous pour répondre Voir 1 réponse(s)

08/09/2022

 Toyota Phil Rochette (160Pts.)

0

2012 Sienna EVO One Thar toy9 crank no start and no headlights

2012 Toyota Sienna G-Key with EVO-ONE & THAR-ONE-TOY9 & THAR-ONE-TOY1 & RF642W. EVO-ONE & THAR-ONE-TOY9 & THAR-ONE-TOY1 & Rf642w The car cranks but does not start when remote started. It does start manually with the evo one isntalled. The RF kit was put in mode 1. After having pluged installed the EVO-ONE with the harnesses, the headlights dont work, turn signals are fine. When programming the rf kit only the instrument cluster lights blink, not the healights and no horn. service # 002B04044516
Connectez-vous pour répondre Voir 1 réponse(s)

10/04/2022

 Toyota KIEN MACH (210Pts.)

0

2011 Sienna G-Key No tachometer signal

I've installed Evo-one, remote starter RFK442 with Toy9 wiring packets. Connect and flash exactly the same with the Toy9 instruction. After all, I can start with remote starter but the vehicle failed to be ON. And flashing 4* parking light (no tachometer signal). Is there any solution for this problem? Thank you. P/S: my S/N is 002B04 241048
Connectez-vous pour répondre Voir 1 réponse(s)

23/10/2021

 Toyota Bobby B (390Pts.)

0

Why is the Fortin remote operating the sliding doors instead of normal operation - Sienna?

Hello. EVO RS4 kit (EVO-ALL with RM442 remotes) on a 2014 Toyota Sienna. Factory remote operates perfectly. Both Fortin remotes are operating the sliding doors instead of normal lock/unlock and start functions. I press the lock button and the driver side sliding door opens. Unlock opens the passenger sliding door. Pressing the start sequence opens both doors. The Fortin remotes will not lock, unlock or start the vehicle. Any advice?
Connectez-vous pour répondre Voir 1 réponse(s)

12/08/2021

 Toyota Bobby B (390Pts.)

0

2014 TOYOTA SIENNA EVO ALL OR EVO ONE

I apologize if this is a repeat question but I couldn't find an existing answer.  I have a 2014 Toyota Sienna with PTS.  I don't intend to install any 3rd party remote starter.  Will the EVO ALL work for remote start on its own or will I need to install the EVO ONE?

Connectez-vous pour répondre Voir 1 réponse(s)

09/12/2019

 Toyota Mark Spicer (130Pts.)

0

Sienna 2015 Push-to-Start tx - rx wires?

No specs on Tx and Rx wire location for 2015 Sienna Push-To-Start
Connectez-vous pour répondre Voir 1 réponse(s)

08/12/2019

 Toyota akm (850Pts.)

0

2011 Sienna starting issue with evo-one

I am using Toy9 harness with Evo one for 2011 Toyota Sienna key start. As i understand this vehicle cannot be started with 3 time lock so i added Evo start 2. Installation went well but when starting through Evo Start 2 app, can keep cranking but not starting. It is starting normal with key. With regular key start, evo one is showing yellow light. Not sure what i missed as i am flashing first time. SN on back of evo one is 002B04 044517 Appreciate for your help.
Connectez-vous pour répondre Voir 1 réponse(s)

17/11/2019

 Toyota mario aguilera (160Pts.)

0

04 sienna shuts off after 15 seconds with remote start

Installed fortin evo one along with viper remote, the programming went well, but car shuts off after 15 seconds of running with remote start, but stays on if remote is used with the key on the ON position, is it likely a problem with the immobilizer? I noticed the voltate on my battery doesnt move past 12 volts when it runs for the 15 seconds, i guess that's what's telling the virtual tach the car is not on?
Connectez-vous pour répondre Voir 1 réponse(s)

04/10/2019

 Toyota Alexey Kozlov (430Pts.)

0

EVO-ONE does not control parking lights with headlight switch in AUTO position

Toyota Sienna LE 2019, EVO-ONE, THAR-ONE-TOY9, firmware version 79.[54]. EVO-ONE is configured with default/recommended options for my car. Everything is connected using T-harness per Installation Guide #72381. I have the following issue: EVO-ONE does not control the parking lights when the headlight switch is in AUTO position. The issue persists no matter whether it is day or night. So, I cannot read diagnostic codes by counting flashes in that position. Nevertheless, it does control the parking lights when the headlight switch is in DRL-OFF position. How can I fix that issue?
Connectez-vous pour répondre Voir 0 réponse(s)

07/10/2019

 Toyota Alexey Kozlov (430Pts.)

0

Wiring error in THAR-ONE-TOY9 with SIENNA 3rd gen.

A wiring error has been found in the low-current part of T-harness THAR-ONE-TOY9 (THAR-TY30 Rev. 1 LOT: 51096) when installing on Toyota Sienna LE 2019. The remote starter in/out wires for the AUTOLIGHT from EVO-ONE, pins A17 (Green/White) and A18 (Green/Red) are connected to a wrong pin of the Body ECU white 30-pin plug: they are connected to pin #6 instead of pin #28. This results in tripping a signal from the right rear (sliding) door trigger instead of the AUTOLIGHT signal. The problem applies to the installation of this T-harness on all 3rd gen. Siennas. The correct info on the Body ECU white 30 pin plug wiring can be found here: https://www.the12volt.com/installbay/printer_friendly_posts.asp?fid=3&tid=122207 To the contrast, the wiring diagram on the installation guide without this low-current T-harness is correct (Guide #72751), the AUTOLIGHT signal being taken from a different connector (on the steering column).
Connectez-vous pour répondre Voir 1 réponse(s)

03/10/2019

 Toyota Alexey Kozlov (430Pts.)

0

EVO-ONE flashes parking lights 30 times and remote lock command does not work

Toyota Sienna LE 2019, EVO-ONE, THAR-ONE-TOY9, RFALL642W, firmware version 79.[54]. EVO-ONE is configured with default/recommended options for my car. I have the following issue with EVO-ONE when I leave my headlight switch in DRL-OFF position and previously started my car remotely. When I open the door to leave my vehicle, my parking lights flash 30 times. In the Fortin manual, I found error code descriptions only up to 7 flashes. What is the meaning of that 30-times-flashing error code? In addition to that, the LOCK command from my RF kit has never worked but also makes the parking lights flash 30 times. So, I have to use my factory remote instead of the RF kit to lock my vehicle. The other commands from the RF kit (START, STOP, UNLOCK, SLIDING DOORS OPEN/CLOSE) are working fine. How can I fix that?
Connectez-vous pour répondre Voir 3 réponse(s)

03/10/2019

 Toyota Alexey Kozlov (430Pts.)

0

Sienna EVO-ONE pit-stop issue

Toyota Sienna LE 2019, EVO-ONE, THAR-ONE-TOY9, firmware version 79.[54]. EVO-ONE is configured with default/recommended options for my car. I have an issue with the pit-stop mode. I press 3xLOCK while inside the vehicle and engine running, then remove the key from the ignition lock. The engine continues to run but turns off when I open any door. How can I fix that issue?
Connectez-vous pour répondre Voir 2 réponse(s)

02/10/2019

 Toyota Alexey Kozlov (430Pts.)

0

Crimestopper RFALL642W does not work with EVO-ONE

I have connected Crimestopper RFALL642W to Fortin EVO-ONE installed on Toyota Sienna 2019 per Fortin manual https://cdn.fortin.ca/download/33021/rf642w-install-guide-33021.pdf. I have the following issue. When I connect the RF kit to the remote starter the blue LED on the RF kit antenna flashes one time. After that, when I try to program the remote transmitters per the same manual (turning ignition on and off, using the valet switch and brake pedal) I cannot get any antenna LED response. The LED on antenna always stays off and I cannot program the remote transmitters. In addition to that, the button on the RF kit antenna does not work when I try to use it as a valet switch per another Fortin manual. The RF kit is connected to EVO-ONE using a simple cable, not T-harness. EVO-ONE is configured with default/recommended options for my car. The firmware version is 79.[54]. The 3xLock start is enabled and working fine. Do I need to change any options on EVO-ONE so that it can communicate with the RF kit? Is my RF kit faulty?
Connectez-vous pour répondre Voir 1 réponse(s)

17/07/2019

 Toyota Phat Dam (160Pts.)

0

2010 Sienna Limited Remote Start

Hi, Does your evo one support the remote start for 2010 Toyota Sienna Limited? If yes, does it support the factory key fob or i have to buy an aftermarket RF kit? Does it support the Key Takeover feature? And do you have any plug and play harness for this year model? My Sienna has Standard key system. Thanks Pat
Connectez-vous pour répondre Voir 1 réponse(s)

07/11/2018

 Toyota Radoslaw Patora (740Pts.)

0

Toyota Sienna 2008 + EVO ONE no starting Car

Toyota Sienna 2008 -installation guide 58481 ,connection 1 ,program 1 programming bypas is ok -red light blinking and off. car is no running ,no blue light flashing when lock door with keyfob-no reaction Firmware wersion 79.49 - i no try diffrent wersion program -problem is to many times flashing modules is blocked and problem unlock / ask me why used one module to many cars -to many times fortin not working and try second modules,sometimes from customer car when remote work perfect. service no :002B07213899 No answer ok-more connection/diagram is bad no only for this car Guide 58481 is incompletely and no answer and no help from fortin I installing last 10 maybe 12 fortin products from my stock and change company
Connectez-vous pour répondre Voir 1 réponse(s)

07/11/2018

 Toyota Allahan Soung (130Pts.)

0

2014 Toyota Sienna (G key) keyless entry clicks but door lock don't lock/unlock

I have Evo One w/ Compustar Rf remote kit (Rf-2WG9-SP), when I press the lock or unlock on the remotes the Evo-One clicks and lights blinks but the door doesn't lock/unlock. But if I remote start the vehicle while engine running I press unlock the power lock works, but if I turn off the vehicle and press lock it will not lock the doors (Evo-One clicks & lights blinks). Sometime when I'm driving the power door locks will lock/unlock by it's self, thought that was kinda weird. Lmk whats your thoughts, Thanks. -Al
Connectez-vous pour répondre Voir 1 réponse(s)

15/10/2018

 Toyota Jason Zoski (150Pts.)

0

2018 Toyota Sienna push to start- Unable to program Evo-One (step 4)

I have the Evo-one installed in a 2018 Toyota Sienna with push to start. On step 4, push start button twice to turn on ignition, there is no response from the evo. The blue led remains lit and fails to flash. I have checked the wiring and the evo is flashed to the recommended versions. Thanks for your suggestions.
Connectez-vous pour répondre Voir 2 réponse(s)

05/10/2018

 Toyota Olivier Gardner (160Pts.)

0

Toyota sienna 2014

Salut j'ai installer un evo one avec le t connector thar one toy9 mon problême est un coup passer la programmation du module evo one , je ne suis pas capable de programmer le rf kit941w la del bleu de l antenne de flash pas seulement si je la déconnecté et reconnecter elle flash 1x mais si je mets la clef à off et on il ne se passe rien est ce un problême de filage ou de programmation avec le flash link pourtant j avais bel et bien mit l option del active
Connectez-vous pour répondre Voir 1 réponse(s)

01/10/2018

 Toyota Bryan Higgins (570Pts.)

1

Sienna with EVO-ALL + RF642W was working - remote start function yields 6x light flash

Installed EVO-ALL and RF642W on 2015 Sienna. Everything was working perfectly for a few months including remote start via the 2-way RF extender remotes plus the 3x LOCK on factory fob. Now if I send a remote start command, the parking lights flash 6x. This happens with both the factory fob (3X LOCK) and the RF extender remote. All other functions on the RF remote work correctly (lock, unlock, rear liftgate, and both sliding doors), which tells me that some part of the communications are reaching the van's data bus. What does the 6x light flash represent for an error code? The install manual includes nothing on error codes. Also, the 6x light flash - is that possible to have that originate in the RF extender or is it only possible to be a EVO-ALL related error code? Thanks, Bryan
Connectez-vous pour répondre Voir 2 réponse(s)

12/08/2017

 Toyota Loth Sipha (130Pts.)

0

Sliding Door and Power Lift Gate Does Not Work When Remote Started

2017 Toyota Sienna H-Key Options are set based on installation/wiring guide 31121 rev 20170503. I can remote start vehicle and I have it wired up to open the right sliding door and power lift gate but when I remote start the vehicle, I cannot operate them via the key fob. Module shows blue LED when I press either button on the fob. I can manually open the door/lift gate once I unlock the vehicle using the key fob. If I don't remote start the vehicle, everything works as usual. Bypass firmware 79.42. Options A1-A10, C1 and D2 are enabled. Vehicle has OEM Alarm with hood switch bypassed. Remote Start firmware 1.21. Tried both options 25.1 and 34.3 separately, still doesn't work. Options 38 is set at 38.5 (personal preference).
Connectez-vous pour répondre Voir 2 réponse(s)

15/01/2016

 Toyota Gram Lockling (190Pts.)

1

2015 Sienna H-Key (as of Jan 2016)

Hi, I'm buying a 2015 Sienna with H-Key (no push button). Will the EVO-ONe (with T Harness) be all that is required to remote start this vehicle or is additional hardware required? Will an H-Key need to be hidden inside the vehicle? Will the LOCK LOCK LOCK function be able to used to start the vehicle remotely? Thank you.
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer