Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

Nitro will not start almost a year later

I have a 2007 dodge nitro that worked perfectly when i installed it in january of 2016 , now when i press my remote 3 times it takes a while to register and when it does it tries to start very faintly but doesnt start. Im sure its a real simple solution and my wife has loved it so far , just needed some help on resovlving this issue. Thanks for your help

1

2008 Nitro. Do I need a brake switch input ?

I dont see a brake pedal switch hookup for this system like I have with other systems. Do I need one ?

0

Do i need a hood pin for my evo-chrt5 kit?

I purchased the evo-chat5 for my 2007 dodge nitro, do i need anything else or a hood pin?

0

ignition out from crimestopper sp 502

I am installing a crimestopper sp 502 with a chr t5 on a 2009 dodge nitro, do I need to install a diode on the yellow wire coming from the t-harness so that the alarm/remote start does not back feed the unit? or do I just hook up the 2 yellows to the pink directly? this is my last connection everything else is finished, I have read horror stories about people burning up ignitions dont want that. I am using d2d and thepink wire is labeled ignition 1. thanks

0

Diode on ignition wire?

2009 dodge nitro, evo-chrt5 and crimestoppeer sp-502. Do I need to install a diode on the yellow ignition wire?

1

FAQ - SKREEM Service Bulletin 08-003-13

On January 15, 2013, Daimler/Chrysler Corporation released a Service Bulletin for some SKREEM/WCM modules. The subject of the bulletin, "The Radios Clock Loses Time".

 

Problem:

Customer may notice that the clock, over time, loses about a minute per month and needs readjustment

Affected Models: Jeep Wrangler (2009-2012), Jeep Liberty (2009-2012), Dogde Nitro (2009-2011)

 

Solution:

The Chrysler/Dodge/Jeep service bulletin involves the replacement of the Wireless Control Module (WCM) / Sentry Key Remote Entry Module (SKREEM). After the replacement is done and if the vehicle had an EVO installed, the vehicle may start experiencing theft lights issues (theft light will flash non stop when remote starting).

**Important** Being that the module was replaced with a newer SKREEM / WIN (similar to a 2013 Wrangler), several points will have to be taken into consideration:
 

If an EVO-CHR was previously installed in the vehicle, it will have to be replaced with an EVO ALL. The EVO-CHR does not cover/support newer SKREEM / WIN modules. Since the replaced module is similar to the 2013 Wrangler, the MUX connection may not be required.

 

Note: The EVO-CHR is not to be confused with an EVO-CHRT3/4/5 or 6 (these models are actually an EVO-ALL + dedicated T-Harness).

1

Dodge Nitro 2011 "Heat" 4x4 with Advanced Keys install

I am getting a Advanced Keys (http://advancedkeys.com) setup that, as per the manual says, hooks up directly to a Fortin EVO-CHR + T Harness(T2). Now this manual is pretty old, say back in 2007 or so, and now a lot seems to have changed.

 

The guide on this website points to the THAR-CHR5 as the box i would need for my car. However, i dont see much of the color wires the same (and output locations) as it has in the manual i got from Advanced Keys.

 

Could anyone from Fortin be so kind in re-working this setup in the manual below so it points to the correct wires for the THAR-CHR5 instead of the EVO-CHR + T Harness(T2)?

 

I also would like to know what letter (A, B, or C) I would need to choose once I start installing it with the Advanced Keys kit. I see i have 3 options for my Nitro:

(1) With Data-Link
(2) Without Data-Link
or
(3) Stand alone

1

RS232/USB/Arduino communication from PC to EVO ALL

I am wondering if the EVO ALL can be hooked up to a microcomputer (arduino) via UART or using an RS232/USB to a computer? I am wanting to control my canbus in my 2011 Dodge Nitro Heat 4x4 like windows up/down, door locks, RPMs, Break, etc. Is this possible using the EVO ALL (http://ifar.ca/en/vehicles/dodge/nitro/2011/) that your company offers?

 

If thats not possible can i get any type of RF remote and program the buttons to, say, unlock the door, lock the door, etc?

 

Also, is there a push button start for this car?

 

1

11 nitro no range

11 nitro stand alone is there a range extender avaliable

0

2011 Didge Nitro won't remote start after install.

I have a 2011 Didge Nitro and installed an evo-all and thar-char5. Installed everything except the parking light and external input and went thru the program procedure. Followed every step and and blue led turned off after hitting the lock button(means programmed right?). Tried hitting the lock button 3x but the car didn't try to start. What do I do?

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue