Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

29/01/2024

 Audi JW (160Pts.)

0

Reason why turned off after remote start

After installing the Lock x3 remote starter and I checked work well. also I flashed the engine to turn off after 15 minutes. But there are situations where the engine turns off when I open the driver's door after starting the remote start. Even though it hasn't been 15 minutes.

It's happens sometimes. What's the problem?

Login to reply View 1 answer(s)

15/03/2022

 Audi Christopher Edgett (210Pts.)

0

4x Lock Required to start Audi 2012 S4 with EVO-ALL+THAR-AUD1

2012 Audi S4 with Push button start, automatic trans, Installed EVO-ALL+THAR AUD1. (latest firmware confirmed with flashlink)

If the canbus is alive, the car will start on 3x lock of oem fob.

If the car is asleep, as in it sits overnight then "4x" lock is required to start the engine.

Something I've also noticed is 3x lock does not stop the engine when it has been started by the EVO-ALL module..so if engine is started with fortin module, no amount of fob lock button pressed will not stop the engine.

The system was updated with flashlink during the install process and only setting changed was the start run time length from 5mins to 30mins.

All the wiring that is required with the THAR-AUD1 has ben double checked and as mentioend, if canbus is live it'll start perfectly fine on 3x lock, it's just when the vehcle is asleep it's like you need to press the remote 1x to wake up the canbus and then 3x to start the engine. 

The 3x lock to shut off engine after start with fortin system, I'm not sure if this is possible or correct so I'm not 100% this is a concern.

Is any of the above normal operation?

Login to reply View 1 answer(s)

06/01/2021

 Audi jeremy vermeulen (670Pts.)

0

looking for a no key required for Audi A4 and Q7 2017-2020 solution using thar-aud2

i am looking for a bypass soloution for 2017-2020 Audi A4 and Q7 models that do not require a sacrifice key. also want to be able to use t harness to avoid splicing the wiring in the vehicle. the customer only has one operational key for the vheicle.
Login to reply View 1 answer(s)

07/01/2020

 Audi chris lo (350Pts.)

0

audi a$ EVO AUDT1 remote start engine running put key in car died

all programes done, remote start engine running get inside the car pressed brake pedal engine still running also can drive without key and trying put key in engine died, what is the problems//???
Login to reply View 1 answer(s)

02/03/2019

 Audi George Stojanovski (210Pts.)

0

Dryptor limit reached has been reached for this car

Please help, i have connected theevo-all bypass using THAR-AUD1 harness to my 2014 SQ5 TDI. I have programmed unit as per guide 77161 and all goes as per instructions. I try to dcrypt and i get the message about limit reached for this car. I did successfully dcrypt the bypass the first time i tried but couldnt get the 3x lock to start the car so i reset the unit and tried to dcrypt again from the benining and now it wont work.
Login to reply View 0 answer(s)

24/02/2019

 Audi George Stojanovski (210Pts.)

0

Wont start and dcryptor limit has been reached for this car EVO-ALL and THAR-AUD1

Remote start not working with 3x lock. Car is 2014 Audi SQ5 TDI push to start auto, options C1, D6, D1.3, D1.10 all activated as per installation instructions. Key was dycrypted successfully and updated. No hood pin installed for testing. Spliced into can wires under steering column and connected to brake activation all as per instructions for EVO-ALL and THAR-AUD1 harness. 3x lock and nothing happens, no lights flashing on evo-all. Hardware Vr: 6 Firmware Dr: 60.02 SInce it wasn't working i reset the bypass and tried to dcrypt the key again and now i get dcryptor limit has been reached for this car.
Login to reply View 1 answer(s)

07/02/2019

 Audi Christopher Edgett (210Pts.)

0

Nano Start V3 Replacement Remote

2012 Audi S4 push button start DSG.

 

Lost the remote fob and need to replace (lost in transit when railing car from montreal to outwest). Car is from Montreal but recently moved to British Columbia, closest distributer is 5 hours away.

 

I accessed the module under dash, it's a Nano Start, Hardware V3. Firmware V10.17.

 

I have the installation manual to program the unit not sure of which remote and where to buy online,

    What's the model# for the fob replacement? Is there a place to order the remote fob online?

(Also can this nano start have something added to use the oem key to 3x-lock-start?)

Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue