Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

14/01/2017

 Ford Bernie Surber (190Pts.)

0

Evo ALL with Ford THarness 2012 Ford Fusion

I have hooked up all connections except for driver door pin because I can't seem to find the correct wire. When I hold the program button and plug in the black 4 pin connector to start programming, nothing happens. No lights come on or anything. When I plug it back in to the Flashlink it comes on and shows the info. Am I missing something? I have my only vehicle dissasembled and really need to get this done. PLEASE HELP Update: I checked the red and black wires on the black 4 pin plug and there is 12.5 volts at the connection. Is this a bad unit? Update part 2: I flashed with an older version of firmware and then reflashed back to current/recommended firmware and it finally cooperated! Up and running. I do have one final question though, I did not hook up the left door pin wires because I couldn't find the correct one to use. What functions will I not have because of this? I have noticed that the car will only turn off if I press the brake. Any ideas?? Sory for the long post, just trying to do it right. Thanks!
Login to reply View 1 answer(s)

05/01/2017

 Ford shigadeyo (210Pts.)

1

2012 Ford Fusion Quesions

I have several questions regarding the  Fortin EVO-FORT1:

    Is the Fortin EVO-FORT1 compatible with 2012 Ford Fusion HYBRID?  I ask because I don't see the Hybrid option listed for 2012 on the Fortin web site product selection lists. CAN High/Low Taps -- Can these connections be made with T-Taps or must they only be wrapped and taped or soldered? Driver Door Pin -- Is is pin 9 as listed in the install guide or 14 as listed in another quesion asked in this forum? Parking Light -- Is this connection required?  If so, can the incoming 12V to relay pins 86 and 87 be fused at 10A rather than from relay pin 30 to the parking light wire? Options -- I have the following options enabled.  Are they correct/am I missing anything?
      A1-A11 enabled EXCEPT A5 as listed in the installation guide B1 enabled C1 enabled D1+D1.6 enabled D4 enabled D5 enabled

Thank you for the help!

 

Login to reply View 1 answer(s)

25/09/2015

 Toyota Nathan Cheng (130Pts.)

0

Manual Corolla no door switch signal

Everything works in automatic mode (loop cut). I've done the tach learning, I've called tech support and got my clutch switch right. When I come to do the ready mode procedure the car stays on even after door is open and shut. It looks like its not detecting the door switch properly but yet I've tried to ground my wire directly. Still doesnt work
Login to reply View 1 answer(s)

21/08/2015

 Ford Dinesh Koya (780Pts.)

0

Driver Door Pin to A17, A18 required for 2014 Ford Focus manual trans?

I am installing a remote starter in 2014 Ford Focus manual transmission. Do I need to connect the driver door pin wires to A17 and A18 of EVO-ALL in order to turn off the radio after the remote starter shuts down?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue