English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

27/12/2023

 Mazda Mmk005 (130Pts.)

0

Evo Start 2 not working with Evo one with T Harness Thar one Maz3

Hello,

I recently bought Evo start 2 for my Evo one which I have been using for more than 2 years on my Mazda cx 3 2019 with T harness. At that time I did not choose the app start option while programming the Evo one. Can some please help me where should i be connecting the Yellow wire. Does it goes into the A1. Also none of the other options like door unlock are not working. Do I have to reprogram the Evo one again. I know that the firmware should be atleast 1.21. When i push start from the app the green light on the evo start 2 is turning on but nothing is happening.

I have followed the following steps and it was not working.

Ignition ON - OFF - ON (While holding the brake?)

Press and release brake 4 times

Press and hold the Evo start button until green

Turn OFF Ignition

Thank you for reading any kind of help or suggestions is much appreciated 

Connectez-vous pour répondre Voir 1 réponse(s)

12/04/2021

 Mazda Jaime Penaranda (190Pts.)

0

Yellow, blue and red lights keep flashing when I plug evo-all in.

Flash unit using flash-link via PC. Even tried reset,.same outcome. SN: 001 A07 214660 Flash successfully. Status light change when trying ti program, but does not take program correctly.
Connectez-vous pour répondre Voir 1 réponse(s)

11/01/2021

 Mazda Robert giuntoli (130Pts.)

0

evo one install with t harness no start

2015 mazda 3 manual no start red light flashing blue light come on when pushing remote
Connectez-vous pour répondre Voir 1 réponse(s)

05/11/2020

 Mazda Philip Feldman (130Pts.)

0

EVO-ONE not responding to programming (2008 Mazdaspeed3)

Edited

During 2x key programming on my 2008 Mazdaspeed:

1. Hold program button, plug in main power connector, release when LED is red.

2. Plug in main 20 pin connector and 5 pin communication (CAN) connector into fortin.

3. Cycle first key into IG-ON (2) position and wait 3 seconds -> EVO Red light turns off, yellow light turns on.

4. Remove first key -> EVO yellow light turns off, red light turns on.

5. Insert second key into IG-ON (2) position and wait 3 seconds -> EVO red light stays on.

6. remove second key and within 5 seconds press and release program button ->  After this I can get different results, but the ignition never engages on its own:

a. EVO clicks once (relay?) and red light stays on. Car alarm is armed and will not allow me to start vehicle. Unplugging main EVO power connector reverts the car alarm to functional.

b. Nothing happens, LED remains Red.

In step 8 of the guide, it says the cars ignition will turn on (does not indicate that I should turn it on). This does NOT occur.

However, If I (within the 5 seconds after pressing program button) insert the key into IG-ON(2), The red light blinks 10 times, then the blue light blinks rapidly. Then they both go off, the unit clicks (relay) and only the yellow light stays on solid. This is what the guide says should happen without me turning on the ignition.

More info:

Trunk (I have hatchback) and hood safety switch are not connected.

I am programming the OEM remote for 3x lock remote starting.

Firmware updated November 4th with:

- Unit options: C1 and D2

- Function 8-5, 34-3

All wires pass continuity check between EVO and vehicle connector pin.

Connectez-vous pour répondre Voir 2 réponse(s)

05/01/2020

 Mazda Thomas Leland (300Pts.)

1

Can anyone confirm Dcryptor servers are functional at the moment?

Dcryptor has been getting stuck at 'processing update' on multiple attempts since yesterday for me. The EVO-ONE responds with the correct LED sequences when configured in the car before decryption. I have also tried multiple computers and uninstalling/reinstalling the program. This is for an EVO-ONE + THAR-ONE-MAZ3 in a 2018 Mazda CX-5.
Connectez-vous pour répondre Voir 2 réponse(s)

12/12/2018

 Mazda Radoslaw Patora (740Pts.)

1

MAZDA CX5 2018 AUTOMATIC + EVO ONE ,CRUISE CONTROL NOT WORKING

Installed EVO-ONE with THAR-ONE-MAZ3 following Guide 68261 on a 2018 CX-5 automatic. All options left default except those specified in the install guide (set C1, set D2, and function 38 mode 2.) Remote start works, however, when I get in the car and drive off, cruise control will not set. I can enable cruise control mode but it will not set. If I start the car normally, however, the cruise control works as expected. So it is only after a remote start that the cruise control will not engage.

Connectez-vous pour répondre Voir 1 réponse(s)

30/03/2016

 Mazda Jerry martin (780Pts.)

0

mazda cx-5 doesnt remote start

installed an evo-one in a cx-5 everything went good done the programmation 1-12 went good done it a second time and i only get a yellow light not the usual red and blue .tried to progarm the blue led and it start to alternate red-yellow-blue then blinks blue like when you program with one key fob.tried to remote start without success park light lights up when trying to start and then turn off and doesnt blink only thing that blinks is the blue led on the rf antenna as it blinks 4 times
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer