English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

26/03/2021

 Hyundai Kevin Raymond (250Pts.)

0

Evo One won't start after 5 min or so but was working right after key bypass programming procedure

Hi, I'm kind of lost here, nobody seem to have the answer to my problem, not even Fortin when I call them for help. I installed my Evo One on my Hyundai Tucson 2020 standart key start, followed exactly all the wiring as per the guide, double check all my connection (EMS, CAN BUS, ignition wires, etc) and there's no loose cable. After that I did the key bypass programming procedure with EMS cable : hold down program button while plugging the 6 pin heavy gauge wire till it was red, plug all the others wires, press 7 times program button till it flash 6 times every second, put the key in and turn to ON. At this point the red led flashed 10 time quickly and after stayed on while the blue light started flashing quickly too. After that I turned Ignition to OFF and every light turn off. Right after that I tried to start the car by pressing LOCK, UNLOCK, LOCK and the car started no problem. I then stop the car, close the door and wait... 5 min later, I tried to restart the car with the remote starter but it didn't work. The car got the lock unlock lock signal but no light is flashing on the module anymore like if it went into sleep mode or something. I tried many thing and here is what I found out : - If I unplug all cable from the Evo One and plug it straight back it then start receiving signal again for the next 5 min or so. - If I open the trunk and close it back, the module seem to start back receiving signal from oem remote. To me it feel like there is a cut off or something that stop the module from receiving any signal from the oem remote after a certain amount of time, kind if it was to prevent from draining the battery of the car. Could also be that the Evo One is loosing the key programming after current shutting off in the car but then it shouldn't start by just unplugging and replugging the 6 pin ignition wires. *Sorry if my english is not perfect, I usually speak french.
Connectez-vous pour répondre Voir 2 réponse(s)

10/01/2021

 Hyundai Stephen Renna (260Pts.)

0

2019 veloster push to start not working

I just installed the Evo-One with the T harness. I programed the Evo and the started the car. Followed the reservation mode and the hit the push to start button and the car shuts off! I notice that when the car is on the Evo-One only shows a orange/yellow light, that's it. Please help.
Connectez-vous pour répondre Voir 0 réponse(s)

08/05/2019

 Hyundai Brandon Houston (190Pts.)

0

2016 Hyundai Accent won't start with t harness install

My car will start with key but not remote start theBLUE LIGHT STAYS ON CONNECT REST OF CONNECTORS TURN KEY ON LIGHT GOES OUT turn key off blue light goes back on can voltage is 2.7 and 2.5
Connectez-vous pour répondre Voir 1 réponse(s)

08/05/2019

 Hyundai Brandon Houston (190Pts.)

0

IS AN RF KIT NEEDED WHEN INSTALLING INTO 2016 HUNDAI ACCENT STANDARD KEY W/ T HARNESS

I have a 2016 Hyundai Accent standard key Evo One with a t harness is a rf kit needed for installation
Connectez-vous pour répondre Voir 1 réponse(s)

26/04/2019

 Hyundai Sebastien Bordeleau (240Pts.)

0

Auto usagé avec evo start problème...

Bonjour, j'ai acheté mon Auto usagé au concessionnaire kia. Et l'auto vien avec evo start. Le code actuel est utilisé par l'ancien propriétaire . Donc comment retirer l'ancien propriétaire si j'ai zero possibilités de contact avec lui....?

 

Merci

Connectez-vous pour répondre Voir 1 réponse(s)

20/10/2018

 Hyundai Rogelio Abraham2 (270Pts.)

0

Evo one, remote started run's and quit in 5 seconds

Evo one, remote started with RFkit RM411 runs but quit in 5 seconds ( remote starter attempted twice ) and failed. whats wrong? please help..
Connectez-vous pour répondre Voir 1 réponse(s)

17/01/2017

 Hyundai Neseth Kong (200Pts.)

0

Evo One can't Program Compustar G9 2 way

I have an EVO ONE which i installed in my 2016 Tucson with the T harness.  The wiring was minimal and straight forward, so I know it's all correct.  It's just 4 CANbus wires, parking lights, horn, and ignition.  The dealer I bought it from programmed it for a Revo 1.1(fortin2) but I couldn't get that to work.  I followed the procedure for the valet button and brake pedal, the car responds and flashes the lights when it's supposed to, but wouldn't respond when pressing the start button on the Revo.  So I sent those remotes back to the dealer to be replaced. 

While waiting for the replacement remotes, I was at best buy and spotted the compustar 2 way system (RF-2WG9-SP).  I bought it and ordered the flashlink2 unit online.  First, before the flashlink arrived, I swapped the 4 pin wires and programmed the remotes with the EVO ONE still set to fortin2 and firmware 1.21, and the compustar remotes WORKED.  I could Lock/Unlock my doors and hatch, as well as start the car.  The car responds exactly as it should with the lights and horn.  The problem is it only works as a one way remote.  The blue compustart remote is supposed to be one way, but the orange remote is supposed to give me a 2 way response.  However, at least I know all of my wiring is correct. So the problem is communications handshaking between the box and the remotes.

So my Flashlink comes in and i'm able to switch the options to firsttech from fortin2.  I tried to program the remotes on mode 1 and mode 5, but no success.  I tried to do a full master reset and flashed the firmware to 0.96.  I set it to firsttech in options and tried to program on mode 1 but didn't work.  So i did a master reset, set options to firsttech and tried to program on mode 5 but no success.  So I set it back to fortin2 and it programmed on mode 5 on the first try.  Everything works again except only as a 1 way remote.

Any ideas, I figured it would be straight forward to program this remote?

Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer