English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

10/04/2023

 Subaru jared halterman (160Pts.)

0

Car starts then immediately dies when I don’t use remote start

Remote start works fine but when I use the key to start like normal car dies immediately
Connectez-vous pour répondre Voir 1 réponse(s)

24/09/2022

 Subaru Timothy Mainusch (190Pts.)

1

2015 Subaru Legacy PTS starts and shuts down 2 seconds after, then it tries again and shuts down 2 seconds after

No T-harness. Programmed ok, Dcryptor ok. Updated after Dcryptor process. I have updated the module to current 84.12. I swapped the blue/black wire with the yellow green on the cut IMO. Still no start or LED.
Connectez-vous pour répondre Voir 1 réponse(s)

07/01/2018

 Subaru Jory S (520Pts.)

0

EVO ONE alarm with OEM remote?

2016 Subaru Forester, Standard Key, OEM Remote, No Factory Alarm

EVO ONE recently installed and everything works as expected using 3X lock with OEM remote.  Is it possible to take advantage of the built-in EVO ONE alarm while still using the OEM remote?  With option 9.1 & 14.2 enabled, the alarm is armed when the doors are locked, but I can't figure out how to disarm the alarm on unlock with the OEM remote (instead, the alarm is triggered when unlocking with OEM remote and opening door).  Is this possible with the OEM remote or only with an RF kit?

Connectez-vous pour répondre Voir 1 réponse(s)

07/01/2018

 Subaru Jory S (520Pts.)

1

Shut off with OEM remote (after starting remotely)?

2016 Subaru Forester, Standard Key, OEM Remote, No Factory Alarm EVO ONE recently installed and everything works as expected using 3X lock with OEM remote. Is there a way to turn off the vehicle with the OEM remote after starting it remotely? I tried 3X lock after starting it but that didn't work. I didn't see any other options in the firmware. Is this only possible with an RF kit?
Connectez-vous pour répondre Voir 1 réponse(s)

05/10/2017

 Subaru Jeremy Jedlicka (180Pts.)

0

EVO-ONE + THAR-ONE-SUB1 for 2018 CrossTrek

I just purchased a 2018 CrossTrek Premium regular key with EyeSight. Just want to verify that the EVO-ONE with the THAR-ONE-SUB1 T Harness is compatible with the new model year and the 2017 wiring information from this website will work.
Connectez-vous pour répondre Voir 1 réponse(s)

06/02/2017

 Subaru Heath Ekin (130Pts.)

0

Oem key fobs dont work now, need help. 2016 impreza evo one

I've triple checked the wiring. Done the programming dcryption, master resets, and firmware updates. Enabled 38.2 c1 and d5. The car will start with key but no remote access.
Connectez-vous pour répondre Voir 1 réponse(s)

06/12/2016

 Subaru felipe sesnich (160Pts.)

0

2015 crosstrek program OEM RF transmitter lo enable 3x start.

 

2015 CROOSTREK WONT REMOTE START. HOW DO I PROGRAM OEM RF TRANSMITTERS TO REMOTLY START VEHICLE.

I FOUND THIS TROUBLESHOTING THE EVO-ONE. 

DECRYPTOR DONE AND UPDATED , INSTALLED BACK TO CAR BUT DOESNT REMOTE START WITH 3X LOCK)

If the red led is not turning on then the module is not receiving a start command. Verify that the RF kit being used was properly programmed.

If it does turn on briefly then shut off right away, pay attention to the parking light flashes. 

Connectez-vous pour répondre Voir 2 réponse(s)

30/01/2016

 Subaru shemis.pro Alex (200Pts.)

0

EVO-ONE wont start with oem remote with factory alarm.

Service no 002B05 027677

 

Hello.  I`m trying to take a work EVO-ONE for subaru outback 2011, automatic transmision, with  factory alarm. so loop is cuted. i used GUIDE # 46701 for harness conection. turning on ignition yelow light goes on. when i pushing lock button 3 times nothing going at all (blue light- no, red light - no). is there problem in incorrect flashing?

 

Service No: 002B05 027677 Preload date: 47-2015 Hardware version: 5 Firmware version: 1.17 Recommended version: 1.16    

 

Connectez-vous pour répondre Voir 2 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer